added an example, mt

diff --git a/base/startup_example.sh b/base/startup_example.sh
new file mode 100755 (executable)
index 0000000..23d7cb8
--- /dev/null
+++ b/base/startup_example.sh
@@ -0,0 +1,53 @@
+# example startup file, tailored for trb046
+
+# You *have* to adapt the trbnetaddresses to get the CTS running
+# Also the destination MAC address has to be changed if you want to see data
+
+##### TRBNET #####
+# set the TRBNet addresses of the Endpoints
+trbcmd s 0xb000000390381d28 0 0x0200
+trbcmd s 0xa300000390381328 1 0x0201
+trbcmd s 0x4800000390381628 2 0x0202
+trbcmd s 0x1700000390382028 3 0x0203
+trbcmd s 0xdc00000390380c28 5 0x8000
+
+##### Ethernet and UDP #######
+trbcmd w 0x8000 0x8300 0x8000
+trbcmd w 0x8000 0x8301 0x00020001
+trbcmd w 0x8000 0x8302 0x00030062
+trbcmd w 0x8000 0x8303 0xea60
+trbcmd w 0x8000 0x8304 0x2260
+trbcmd w 0x8000 0x8305 0x1
+trbcmd w 0x8000 0x8306 0x0
+trbcmd w 0x8000 0x8307 0x0
+trbcmd w 0x8000 0x8308 0xffffff
+trbcmd w 0x8000 0x830b 0x7
+trbcmd w 0x8000 0x830d 0x0
+
+#mac address of the EB
+# cbmpc026_eth0: 90:f6:52:03:8f:c4
+trbcmd w 0x8000 0x8100 0x52038fc4 # lower 4 bytes
+trbcmd w 0x8000 0x8101 0x90f6 #upper byte
+
+# destination port and source IP and so on
+trbcmd w 0x8000 0x8102 0xc0a80001 # destination IP 192.168.0.1
+trbcmd w 0x8000 0x8103 0xc350     # destination port: 50000
+trbcmd w 0x8000 0x8104 0xdead8001 # source IP
+trbcmd w 0x8000 0x8105 0x0230     # source port
+trbcmd w 0x8000 0x8106 0xc0a80072
+trbcmd w 0x8000 0x8107 0xc350
+trbcmd w 0x8000 0x8108 0x0578
+
+
+#####  TDC  #######
+# 0xfe48 is the broadcast address of TDC-endpoints in the system
+trbcmd w 0xfe48 0xc0 0x00000001 ## logic analyser control register
+trbcmd w 0xfe48 0xc1 0x000f0005 ## trigger window enable & trigger window width
+trbcmd w 0xfe48 0xc2 0xffffffff ## channel 01-31 enable
+trbcmd w 0xfe48 0xc3 0x00000000 ## channel 32-63 enable
+
+
+
+
+trbcmd w 0x8000 0xa137 0xfffff  #set CTS pulser to 100Hz
+trbcmd setbit 0x8000 0xa101 0x2 #enable pulser channel 0