From f4734720aef21c4214742f19295148681fc04758 Mon Sep 17 00:00:00 2001 From: Jan Michel Date: Thu, 28 Dec 2023 20:08:24 +0100 Subject: [PATCH] include scaler readout into beamabort design --- code/scalers_readout.vhd | 294 +++++ code/tb/sim/scalers_readout.mpf | 1799 +++++++++++++++++++++++++++++++ code/tb/tb_scalers_readout.vhd | 107 ++ shutdownlogic/trb3sc_basic.prj | 4 + shutdownlogic/trb3sc_basic.vhd | 130 +-- 5 files changed, 2232 insertions(+), 102 deletions(-) create mode 100644 code/scalers_readout.vhd create mode 100644 code/tb/sim/scalers_readout.mpf create mode 100644 code/tb/tb_scalers_readout.vhd diff --git a/code/scalers_readout.vhd b/code/scalers_readout.vhd new file mode 100644 index 0000000..17f5970 --- /dev/null +++ b/code/scalers_readout.vhd @@ -0,0 +1,294 @@ +library ieee; +use ieee.std_logic_1164.all; +use ieee.numeric_std.all; + +library work; +--use work.config.all; +use work.trb_net_std.all; + +entity scalers_readout is + generic( + NUM_OUTPUTS : integer range 1 to 7 := 4 + ); + port( + CLK : in std_logic; + RESET : in std_logic; + + BUS_RX : in CTRLBUS_RX; + BUS_TX : out CTRLBUS_TX; + + SIGNAL_IN : in std_logic_vector( 31 downto 0); + TIMER : in TIMERS; + + RDO_RX : in READOUT_RX; + RDO_TX : out READOUT_TX + + ); +end entity; + +architecture arch of scalers_readout is + + type time_arr is array(integer range <>) of std_logic_vector(16 downto 0); + signal CONF_integration_time : time_arr(0 to NUM_OUTPUTS-1); + + type slv_arr is array(integer range <>) of std_logic_vector; + signal CONF_input_select : slv_arr(0 to 1)(31 downto 0); + + signal CONF_delay : std_logic_vector(11 downto 0); + signal CONF_config : std_logic_vector(31 downto 0); --7-0 are pulses + alias CONF_reset : std_logic is CONF_config(0); + alias CONF_number : std_logic_vector(2 downto 0) is CONF_config(10 downto 8); + + + type rdo_state_t is (IDLE, ADDTIME, ADDSCALER, FINISH, BUSYEND); + signal state : rdo_state_t; + + signal long_inp : std_logic_vector(31 downto 0); + signal reg_inp, reg2_inp, reg3_inp : std_logic_vector(31 downto 0); + signal inp_edge : std_logic_vector(31 downto 0); + + signal chain_reset, buffer_reset : std_logic; + + signal delay_in, delay_out : std_logic_vector(NUM_OUTPUTS-1 downto 0); + signal delay_write, delay_read : std_logic; + signal last_delay_read, last2_delay_read : std_logic; + signal delay_count : std_logic_vector(11 downto 0); + + signal reset_timer : unsigned(16 downto 0); + + type scaler_arr is array(integer range <>) of unsigned(19 downto 0); + signal scaler : scaler_arr(0 to NUM_OUTPUTS*2+1); + + signal buffer_write : std_logic; + signal buffer_read : std_logic_vector(NUM_OUTPUTS-1 downto 0); + signal last_buffer_read, last2_buffer_read : std_logic_vector(NUM_OUTPUTS-1 downto 0); + signal buffer_count : slv_arr(0 to NUM_OUTPUTS-1)(16 downto 0); + signal buffer_out : slv_arr(0 to NUM_OUTPUTS-1)(1 downto 0); + +begin + +-------------------------------- +-- Chain Reset +-------------------------------- +PROC_RESET : process begin + wait until rising_edge(CLK); + if RESET = '1' or CONF_reset = '1' then + reset_timer <= (others => '0'); + elsif reset_timer(reset_timer'left) = '0' then + reset_timer <= reset_timer + 1; + end if; + + if reset_timer(reset_timer'left downto 4) = 0 then + buffer_reset <= '1'; + else + buffer_reset <= '0'; + end if; + + chain_reset <= not reset_timer(reset_timer'left); + +end process; + + +-------------------------------- +-- Input Handling +-------------------------------- +long_inp <= (long_inp and not reg2_inp) or SIGNAL_IN; +reg_inp <= long_inp when rising_edge(CLK); +reg2_inp <= reg_inp when rising_edge(CLK); +reg3_inp <= reg2_inp when rising_edge(CLK); + +inp_edge <= reg2_inp and not reg3_inp when rising_edge(CLK); + + +delay_in(0) <= or (inp_edge and CONF_input_select(0)) and not chain_reset when rising_edge(CLK); +delay_in(1) <= or (inp_edge and CONF_input_select(1)) and not chain_reset when rising_edge(CLK); + +-------------------------------- +-- Delay +-------------------------------- +THE_INPUT_DELAY : entity work.fifo_4x2k_oreg + port map ( + Data => delay_in, + Clock => CLK, + WrEn => delay_write, + RdEn => delay_read, + Reset => buffer_reset, + Q => delay_out, + WCNT => delay_count, + Empty => open, + Full => open + ); + +delay_write <= not buffer_reset; +delay_read <= '1' when delay_count >= CONF_delay else '0'; + +last_delay_read <= delay_read when rising_edge(CLK); +last2_delay_read <= last_delay_read when rising_edge(CLK); + + +PROC_BUFFER_COUNTS : process begin + wait until rising_edge(CLK); + if last2_delay_read = '1' then + if delay_out(0) = '1' then + scaler(0) <= scaler(0) + 1; + end if; + if delay_out(1) = '1' then + scaler(1) <= scaler(1) + 1; + end if; + end if; + + if chain_reset = '1' then + scaler(0) <= (others => '0'); + scaler(1) <= (others => '0'); + end if; + + end process; + +-------------------------------- +-- Buffered counters +-------------------------------- + +buffer_write <= last2_delay_read; + +gen_buffers : for i in 0 to NUM_OUTPUTS-1 generate + THE_STORAGE_BUFFER : entity work.fifo_2x64k_oreg + port map( + Data => delay_out(1 downto 0), + Clock => CLK, + WrEn => buffer_write, + RdEn => buffer_read(i), + Reset => buffer_reset, + Q => buffer_out(i), + WCNT => buffer_count(i), + Empty => open, + Full => open + ); + + buffer_read(i) <= '1' when buffer_count(i) >= CONF_integration_time(i) else '0'; + last_buffer_read(i) <= buffer_read(i) when rising_edge(CLK); + last2_buffer_read(i) <= last_buffer_read(i) when rising_edge(CLK); + + PROC_BUFFER_COUNTS : process begin + wait until rising_edge(CLK); + if last2_buffer_read(i) = '1' then + if buffer_out(i)(0) = '1' then + scaler(i*2+2) <= scaler(i*2+2) + 1; + end if; + if buffer_out(i)(1) = '1' then + scaler(i*2+3) <= scaler(i*2+3) + 1; + end if; + end if; + + if chain_reset = '1' then + scaler(i*2+2) <= (others => '0'); + scaler(i*2+3) <= (others => '0'); + end if; + + end process; +end generate; + +-------------------------------- +-- Slowcontrol Registers +-------------------------------- +PROC_REGS : process + variable addr : integer range 0 to 7; +begin + wait until rising_edge(CLK); + CONF_config(7 downto 0) <= x"00"; + addr := to_integer(unsigned(BUS_RX.addr(2 downto 0))); + BUS_TX.ack <= '0'; + BUS_TX.nack <= '0'; + BUS_TX.unknown <= '0'; + + if BUS_RX.read = '1' then + BUS_TX.ack <= '1'; + if BUS_RX.addr(7 downto 0) = x"00" then + BUS_TX.data <= CONF_config; + elsif BUS_RX.addr(7 downto 0) = x"01" then + BUS_TX.data <= x"00000" & CONF_delay; + elsif BUS_RX.addr(7 downto 4) = x"1" and addr < NUM_OUTPUTS then + BUS_TX.data <= x"0000" & (CONF_integration_time(addr)(15 downto 0)); + elsif BUS_RX.addr(7 downto 4) = x"2" and addr < 2 then + BUS_TX.data <= CONF_input_select(addr); + elsif BUS_RX.addr(7 downto 3) = x"3"&'0' and addr < NUM_OUTPUTS + 1 then + BUS_TX.data <= std_logic_vector(scaler(addr*2+1)(15 downto 0)) & std_logic_vector(scaler(addr*2)(15 downto 0)); + elsif BUS_RX.addr(7 downto 3) = x"3"&'1' and addr < NUM_OUTPUTS + 1 then + BUS_TX.data(31 downto 16) <= std_logic_vector(scaler(1)(15 downto 0)-scaler(addr*2+1)(15 downto 0)); + BUS_TX.data(15 downto 0) <= std_logic_vector(scaler(0)(15 downto 0)-scaler(addr*2 )(15 downto 0)); + else + BUS_TX.ack <= '0'; BUS_TX.unknown <= '1'; + end if; + + elsif BUS_RX.write = '1' then + BUS_TX.ack <= '1'; + if BUS_RX.addr(7 downto 0) = x"00" then + CONF_config <= BUS_RX.data; + elsif BUS_RX.addr(7 downto 0) = x"01" then + CONF_delay <= BUS_RX.data (11 downto 0); + elsif BUS_RX.addr(7 downto 4) = x"1" and addr < NUM_OUTPUTS then + CONF_integration_time(addr) <= (BUS_RX.data(16 downto 0)); + elsif BUS_RX.addr(7 downto 4) = x"2" and addr < NUM_OUTPUTS then + CONF_input_select(addr) <= BUS_RX.data(31 downto 0); + else + BUS_TX.ack <= '0'; BUS_TX.unknown <= '1'; + end if; + + end if; +end process; + + +-------------------------------- +-- Trigger Handling +-------------------------------- +THE_RDO : process + variable i : integer; +begin + wait until rising_edge(CLK); + RDO_TX.busy_release <= '0'; + RDO_TX.data_write <= '0'; + RDO_TX.data_finished <= '0'; + + case state is + when IDLE => + if RDO_RX.valid_notiming_trg = '1' and RDO_RX.trg_type = x"E" then + state <= FINISH; + elsif RDO_RX.valid_notiming_trg = '1' or RDO_RX.valid_timing_trg = '1' or RDO_RX.invalid_trg = '1' then + state <= ADDTIME; + end if; + + when ADDTIME => + RDO_TX.data <= TIMER.microsecond; + RDO_TX.data_write <= '1'; + if CONF_number /= "000" then + state <= ADDSCALER; + else + state <= FINISH; + end if; + i := 1; + + when ADDSCALER => + RDO_TX.data(15 downto 0) <= std_logic_vector(scaler(0)(15 downto 0) - scaler(i*2 )(15 downto 0)); + RDO_TX.data(31 downto 16) <= std_logic_vector(scaler(1)(15 downto 0) - scaler(i*2+1)(15 downto 0)); + RDO_TX.data_write <= '1'; + if i = to_integer(unsigned(CONF_number)) then + state <= FINISH; + else + i := i + 1; + end if; + + when FINISH => + state <= BUSYEND; + RDO_TX.data_finished <= '1'; + + when BUSYEND => + state <= IDLE; + RDO_TX.busy_release <= '1'; + + end case; + if RESET = '1' then + state <= IDLE; + end if; +end process; + + +end architecture; diff --git a/code/tb/sim/scalers_readout.mpf b/code/tb/sim/scalers_readout.mpf new file mode 100644 index 0000000..135cf7b --- /dev/null +++ b/code/tb/sim/scalers_readout.mpf @@ -0,0 +1,1799 @@ +; Copyright 1991-2012 Mentor Graphics Corporation +; +; All Rights Reserved. +; +; THIS WORK CONTAINS TRADE SECRET AND PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF +; MENTOR GRAPHICS CORPORATION OR ITS LICENSORS AND IS SUBJECT TO LICENSE TERMS. +; + +[Library] +std = $MODEL_TECH/../std +ieee = $MODEL_TECH/../ieee +vital2000 = $MODEL_TECH/../vital2000 +; +; VITAL concerns: +; +; The library ieee contains (among other packages) the packages of the +; VITAL 2000 standard. When a design uses VITAL 2000 exclusively, it should use +; the physical library ieee (recommended), or use the physical library +; vital2000, but not both. The design can use logical library ieee and/or +; vital2000 as long as each of these maps to the same physical library, either +; ieee or vital2000. +; +; A design using the 1995 version of the VITAL packages, whether or not +; it also uses the 2000 version of the VITAL packages, must have logical library +; name ieee mapped to physical library vital1995. (A design cannot use library +; vital1995 directly because some packages in this library use logical name ieee +; when referring to the other packages in the library.) The design source +; should use logical name ieee when referring to any packages there except the +; VITAL 2000 packages. Any VITAL 2000 present in the design must use logical +; name vital2000 (mapped to physical library vital2000) to refer to those +; packages. +; ieee = $MODEL_TECH/../vital1995 +; +; For compatiblity with previous releases, logical library name vital2000 maps +; to library vital2000 (a different library than library ieee, containing the +; same packages). +; A design should not reference VITAL from both the ieee library and the +; vital2000 library because the vital packages are effectively different. +; A design that references both the ieee and vital2000 libraries must have +; both logical names ieee and vital2000 mapped to the same library, either of +; these: +; $MODEL_TECH/../ieee +; $MODEL_TECH/../vital2000 +; +verilog = $MODEL_TECH/../verilog +std_developerskit = $MODEL_TECH/../std_developerskit +synopsys = $MODEL_TECH/../synopsys +modelsim_lib = $MODEL_TECH/../modelsim_lib +sv_std = $MODEL_TECH/../sv_std +mtiAvm = $MODEL_TECH/../avm +mtiOvm = $MODEL_TECH/../ovm-2.1.2 +mtiUvm = $MODEL_TECH/../uvm-1.1c +mtiUPF = $MODEL_TECH/../upf_lib +mtiPA = $MODEL_TECH/../pa_lib +floatfixlib = $MODEL_TECH/../floatfixlib +mc2_lib = $MODEL_TECH/../mc2_lib +;vhdl_psl_checkers = $MODEL_TECH/../vhdl_psl_checkers // Source files only for this release +;verilog_psl_checkers = $MODEL_TECH/../verilog_psl_checkers // Source files only for this release +;mvc_lib = $MODEL_TECH/../mvc_lib + +work = work +ecp5um = /d/jspc29/lattice/diamond/3.10_x64/ispfpga/vhdl/data/ecp5u/mti/ecp5u +[vcom] +; VHDL93 variable selects language version as the default. +; Default is VHDL-2002. +; Value of 0 or 1987 for VHDL-1987. +; Value of 1 or 1993 for VHDL-1993. +; Default or value of 2 or 2002 for VHDL-2002. +; Value of 3 or 2008 for VHDL-2008 +VHDL93 = 2002 + +; Ignore VHDL-2008 declaration of REAL_VECTOR in package STANDARD. Default is off. +; ignoreStandardRealVector = 1 + +; Show source line containing error. Default is off. +; Show_source = 1 + +; Turn off unbound-component warnings. Default is on. +; Show_Warning1 = 0 + +; Turn off process-without-a-wait-statement warnings. Default is on. +; Show_Warning2 = 0 + +; Turn off null-range warnings. Default is on. +; Show_Warning3 = 0 + +; Turn off no-space-in-time-literal warnings. Default is on. +; Show_Warning4 = 0 + +; Turn off multiple-drivers-on-unresolved-signal warnings. Default is on. +; Show_Warning5 = 0 + +; Turn off optimization for IEEE std_logic_1164 package. Default is on. +; Optimize_1164 = 0 + +; Turn on resolving of ambiguous function overloading in favor of the +; "explicit" function declaration (not the one automatically created by +; the compiler for each type declaration). Default is off. +; The .ini file has Explicit enabled so that std_logic_signed/unsigned +; will match the behavior of synthesis tools. +Explicit = 1 + +; Turn off acceleration of the VITAL packages. Default is to accelerate. +; NoVital = 1 + +; Turn off VITAL compliance checking. Default is checking on. +; NoVitalCheck = 1 + +; Ignore VITAL compliance checking errors. Default is to not ignore. +; IgnoreVitalErrors = 1 + +; Turn off VITAL compliance checking warnings. Default is to show warnings. +; Show_VitalChecksWarnings = 0 + +; Turn off PSL assertion warning messages. Default is to show warnings. +; Show_PslChecksWarnings = 0 + +; Enable parsing of embedded PSL assertions. Default is enabled. +; EmbeddedPsl = 0 + +; Keep silent about case statement static warnings. +; Default is to give a warning. +; NoCaseStaticError = 1 + +; Keep silent about warnings caused by aggregates that are not locally static. +; Default is to give a warning. +; NoOthersStaticError = 1 + +; Treat as errors: +; case statement static warnings +; warnings caused by aggregates that are not locally static +; Overrides NoCaseStaticError, NoOthersStaticError settings. +; PedanticErrors = 1 + +; Turn off inclusion of debugging info within design units. +; Default is to include debugging info. +; NoDebug = 1 + +; Turn off "Loading..." messages. Default is messages on. +; Quiet = 1 + +; Turn on some limited synthesis rule compliance checking. Checks only: +; -- signals used (read) by a process must be in the sensitivity list +; CheckSynthesis = 1 + +; Activate optimizations on expressions that do not involve signals, +; waits, or function/procedure/task invocations. Default is off. +; ScalarOpts = 1 + +; Turns on lint-style checking. +; Show_Lint = 1 + +; Require the user to specify a configuration for all bindings, +; and do not generate a compile time default binding for the +; component. This will result in an elaboration error of +; 'component not bound' if the user fails to do so. Avoids the rare +; issue of a false dependency upon the unused default binding. +; RequireConfigForAllDefaultBinding = 1 + +; Perform default binding at compile time. +; Default is to do default binding at load time. +; BindAtCompile = 1; + +; Inhibit range checking on subscripts of arrays. Range checking on +; scalars defined with subtypes is inhibited by default. +; NoIndexCheck = 1 + +; Inhibit range checks on all (implicit and explicit) assignments to +; scalar objects defined with subtypes. +; NoRangeCheck = 1 + +; Run the 0-in compiler on the VHDL source files +; Default is off. +; ZeroIn = 1 + +; Set the options to be passed to the 0-in compiler. +; Default is "". +; ZeroInOptions = "" + +; Set the prefix to be honored for synthesis/coverage pragma recognition. +; Default is "". +; AddPragmaPrefix = "" + +; Ignore synthesis and coverage pragmas with this prefix. +; Default is "". +; IgnorePragmaPrefix = "" + +; Turn on code coverage in VHDL design units. Default is off. +; Coverage = sbceft + +; Turn off code coverage in VHDL subprograms. Default is on. +; CoverSub = 0 + +; Automatically exclude VHDL case statement OTHERS choice branches. +; This includes OTHERS choices in selected signal assigment statements. +; Default is to not exclude. +; CoverExcludeDefault = 1 + +; Control compiler and VOPT optimizations that are allowed when +; code coverage is on. Refer to the comment for this in the [vlog] area. +; CoverOpt = 3 + +; Turn on or off clkOpt optimization for code coverage. Default is on. +; CoverClkOpt = 1 + +; Turn on or off clkOpt optimization builtins for code coverage. Default is on. +; CoverClkOptBuiltins = 0 + +; Inform code coverage optimizations to respect VHDL 'H' and 'L' +; values on signals in conditions and expressions, and to not automatically +; convert them to '1' and '0'. Default is to not convert. +; CoverRespectHandL = 0 + +; Increase or decrease the maximum number of rows allowed in a FEC table, implementing +; a condition coverage or expression coverage expression, by changing FecEffort. +; Higher FecEffort leads to a longer compile time, but more expressions covered. +; This is a number from 1 to 3, with the following meanings (the default is 1): +; 3 -- High FecEffort, Allows large expressions to be covered, will cause longer compile time. +; 2 -- Medium FecEffort, Allows more number of inputs per expression than Low FecEffort to be covered. +; 1 -- Low FecEffort, Covers only small expressions or conditions and skips larger ones. +; FecEffort = 2 + +; Enable or disable Focused Expression Coverage analysis for conditions and +; expressions. Focused Expression Coverage data is provided by default when +; expression and/or condition coverage is active. +; CoverFEC = 0 + +; Enable or disable UDP Coverage analysis for conditions and expressions. +; UDP Coverage data is disabled by default when expression and/or condition +; coverage is active. +; CoverUDP = 1 + +; Enable or disable short circuit evaluation of conditions and expressions when +; condition or expression coverage is active. Short circuit evaluation is enabled +; by default. +; CoverShortCircuit = 0 + +; Enable code coverage reporting of code that has been optimized away. +; The default is not to report. +; CoverReportCancelled = 1 + +; Use this directory for compiler temporary files instead of "work/_temp" +; CompilerTempDir = /tmp + +; Set this to cause the compilers to force data to be committed to disk +; when the files are closed. +; SyncCompilerFiles = 1 + +; Add VHDL-AMS declarations to package STANDARD +; Default is not to add +; AmsStandard = 1 + +; Range and length checking will be performed on array indices and discrete +; ranges, and when violations are found within subprograms, errors will be +; reported. Default is to issue warnings for violations, because subprograms +; may not be invoked. +; NoDeferSubpgmCheck = 0 + +; Turn ON detection of FSMs having single bit current state variable. +; FsmSingle = 1 + +; Turn off reset state transitions in FSM. +; FsmResetTrans = 0 + +; Turn ON detection of FSM Implicit Transitions. +; FsmImplicitTrans = 1 + +; Controls whether or not to show immediate assertions with constant expressions +; in GUI/report/UCDB etc. By default, immediate assertions with constant +; expressions are shown in GUI/report/UCDB etc. This does not affect +; evaluation of immediate assertions. +; ShowConstantImmediateAsserts = 0 + +; Controls how VHDL basic identifiers are stored with the design unit. +; Does not make the language case-sensitive, affects only how declarations +; declared with basic identifiers have their names stored and printed +; (in the GUI, examine, etc.). +; Default is to preserve the case as originally depicted in the VHDL source. +; Value of 0 indicates to change all basic identifiers to lower case. +; PreserveCase = 0 + +; For Configuration Declarations, controls the effect that USE clauses have +; on visibility inside the configuration items being configured. If 1 +; (the default), then use pre-10.0 behavior. If 0, then for stricter LRM-compliance, +; extend the visibility of objects made visible through USE clauses into nested +; component configurations. +; OldVHDLConfigurationVisibility = 0 + +; Allows VHDL configuration declarations to be in a different library from +; the corresponding configured entity. Default is to not allow this for +; stricter LRM-compliance. +; SeparateConfigLibrary = 1; + +; Determine how mode OUT subprogram parameters of type array and record are treated. +; If 0 (the default), then only VHDL 2008 will do this initialization. +; If 1, always initialize the mode OUT parameter to its default value. +; If 2, do not initialize the mode OUT out parameter. +; Note that prior to release 10.1, all language versions did not initialize mode +; OUT array and record type parameters, unless overridden here via this mechanism. +; In release 10.1 and later, only files compiled with VHDL 2008 will cause this +; initialization, unless overridden here. +; InitOutCompositeParam = 0 + +[vlog] +; Turn off inclusion of debugging info within design units. +; Default is to include debugging info. +; NoDebug = 1 + +; Turn on `protect compiler directive processing. +; Default is to ignore `protect directives. +; Protect = 1 + +; Turn off "Loading..." messages. Default is messages on. +; Quiet = 1 + +; Turn on Verilog hazard checking (order-dependent accessing of global vars). +; Default is off. +; Hazard = 1 + +; Turn on converting regular Verilog identifiers to uppercase. Allows case +; insensitivity for module names. Default is no conversion. +; UpCase = 1 + +; Activate optimizations on expressions that do not involve signals, +; waits, or function/procedure/task invocations. Default is off. +; ScalarOpts = 1 + +; Turns on lint-style checking. +; Show_Lint = 1 + +; Show source line containing error. Default is off. +; Show_source = 1 + +; Turn on bad option warning. Default is off. +; Show_BadOptionWarning = 1 + +; Revert back to IEEE 1364-1995 syntax, default is 0 (off). +; vlog95compat = 1 + +; Turn off PSL warning messages. Default is to show warnings. +; Show_PslChecksWarnings = 0 + +; Enable parsing of embedded PSL assertions. Default is enabled. +; EmbeddedPsl = 0 + +; Set the threshold for automatically identifying sparse Verilog memories. +; A memory with depth equal to or more than the sparse memory threshold gets +; marked as sparse automatically, unless specified otherwise in source code +; or by +nosparse commandline option of vlog or vopt. +; The default is 1M. (i.e. memories with depth equal +; to or greater than 1M are marked as sparse) +; SparseMemThreshold = 1048576 + +; Run the 0-in compiler on the Verilog source files +; Default is off. +; ZeroIn = 1 + +; Set the options to be passed to the 0-in compiler. +; Default is "". +; ZeroInOptions = "" + +; Set the prefix to be honored for synthesis and coverage pragma recognition. +; Default is "". +; AddPragmaPrefix = "" + +; Ignore synthesis and coverage pragmas with this prefix. +; Default is "". +; IgnorePragmaPrefix = "" + +; Set the option to treat all files specified in a vlog invocation as a +; single compilation unit. The default value is set to 0 which will treat +; each file as a separate compilation unit as specified in the P1800 draft standard. +; MultiFileCompilationUnit = 1 + +; Turn on code coverage in Verilog design units. Default is off. +; Coverage = sbceft + +; Automatically exclude Verilog case statement default branches. +; Default is to not automatically exclude defaults. +; CoverExcludeDefault = 1 + +; Increase or decrease the maximum number of rows allowed in a FEC table, implementing +; a condition coverage or expression coverage expression, by changing FecEffort. +; Higher FecEffort leads to a longer compile time, but more expressions covered. +; This is a number from 1 to 3, with the following meanings (the default is 1): +; 3 -- High FecEffort, Allows large expressions to be covered, will cause longer compile time. +; 2 -- Medium FecEffort, Allows more number of inputs per expression than Low FecEffort to be covered. +; 1 -- Low FecEffort, Covers only small expressions or conditions and skips larger ones. +; FecEffort = 2 + +; Enable or disable Focused Expression Coverage analysis for conditions and +; expressions. Focused Expression Coverage data is provided by default when +; expression and/or condition coverage is active. +; CoverFEC = 0 + +; Enable or disable UDP Coverage analysis for conditions and expressions. +; UDP Coverage data is disabled by default when expression and/or condition +; coverage is active. +; CoverUDP = 1 + +; Enable or disable short circuit evaluation of conditions and expressions when +; condition or expression coverage is active. Short circuit evaluation is enabled +; by default. +; CoverShortCircuit = 0 + + +; Turn on code coverage in VLOG `celldefine modules, modules containing +; specify blocks, and modules included using vlog -v and -y. Default is off. +; CoverCells = 1 + +; Enable code coverage reporting of code that has been optimized away. +; The default is not to report. +; CoverReportCancelled = 1 + +; Control compiler and VOPT optimizations that are allowed when +; code coverage is on. This is a number from 0 to 5, with the following +; meanings (the default is 3): +; 5 -- All allowable optimizations are on. +; 4 -- Turn off removing unreferenced code. +; 3 -- Turn off process, always block and if statement merging. +; 2 -- Turn off expression optimization, converting primitives +; to continuous assignments, VHDL subprogram inlining. +; and VHDL clkOpt (converting FF's to builtins). +; 1 -- Turn off continuous assignment optimizations and clock suppression. +; 0 -- Turn off Verilog module inlining and VHDL arch inlining. +; HOWEVER, if fsm coverage is turned on, optimizations will be forced to +; level 3, with also turning off converting primitives to continuous assigns. +; CoverOpt = 3 + +; Specify the override for the default value of "cross_num_print_missing" +; option for the Cross in Covergroups. If not specified then LRM default +; value of 0 (zero) is used. This is a compile time option. +; SVCrossNumPrintMissingDefault = 0 + +; Setting following to 1 would cause creation of variables which +; would represent the value of Coverpoint expressions. This is used +; in conjunction with "SVCoverpointExprVariablePrefix" option +; in the modelsim.ini +; EnableSVCoverpointExprVariable = 0 + +; Specify the override for the prefix used in forming the variable names +; which represent the Coverpoint expressions. This is used in conjunction with +; "EnableSVCoverpointExprVariable" option of the modelsim.ini +; The default prefix is "expr". +; The variable name is +; variable name => _ +; SVCoverpointExprVariablePrefix = expr + +; Override for the default value of the SystemVerilog covergroup, +; coverpoint, and cross option.goal (defined to be 100 in the LRM). +; NOTE: It does not override specific assignments in SystemVerilog +; source code. NOTE: The modelsim.ini variable "SVCovergroupGoal" +; in the [vsim] section can override this value. +; SVCovergroupGoalDefault = 100 + +; Override for the default value of the SystemVerilog covergroup, +; coverpoint, and cross type_option.goal (defined to be 100 in the LRM) +; NOTE: It does not override specific assignments in SystemVerilog +; source code. NOTE: The modelsim.ini variable "SVCovergroupTypeGoal" +; in the [vsim] section can override this value. +; SVCovergroupTypeGoalDefault = 100 + +; Specify the override for the default value of "strobe" option for the +; Covergroup Type. This is a compile time option which forces "strobe" to +; a user specified default value and supersedes SystemVerilog specified +; default value of '0'(zero). NOTE: This can be overriden by a runtime +; modelsim.ini variable "SVCovergroupStrobe" in the [vsim] section. +; SVCovergroupStrobeDefault = 0 + +; Specify the override for the default value of "merge_instances" option for +; the Covergroup Type. This is a compile time option which forces +; "merge_instances" to a user specified default value and supersedes +; SystemVerilog specified default value of '0'(zero). +; SVCovergroupMergeInstancesDefault = 0 + +; Specify the override for the default value of "per_instance" option for the +; Covergroup variables. This is a compile time option which forces "per_instance" +; to a user specified default value and supersedes SystemVerilog specified +; default value of '0'(zero). +; SVCovergroupPerInstanceDefault = 0 + +; Specify the override for the default value of "get_inst_coverage" option for the +; Covergroup variables. This is a compile time option which forces +; "get_inst_coverage" to a user specified default value and supersedes +; SystemVerilog specified default value of '0'(zero). +; SVCovergroupGetInstCoverageDefault = 0 + +; +; A space separated list of resource libraries that contain precompiled +; packages. The behavior is identical to using the "-L" switch. +; +; LibrarySearchPath = [ ...] +LibrarySearchPath = mtiAvm mtiOvm mtiUvm mtiUPF + +; The behavior is identical to the "-mixedansiports" switch. Default is off. +; MixedAnsiPorts = 1 + +; Enable SystemVerilog 3.1a $typeof() function. Default is off. +; EnableTypeOf = 1 + +; Only allow lower case pragmas. Default is disabled. +; AcceptLowerCasePragmaOnly = 1 + +; Set the maximum depth permitted for a recursive include file nesting. +; IncludeRecursionDepthMax = 5 + +; Turn ON detection of FSMs having single bit current state variable. +; FsmSingle = 1 + +; Turn off reset state transitions in FSM. +; FsmResetTrans = 0 + +; Turn off detections of FSMs having x-assignment. +; FsmXAssign = 0 + +; Turn ON detection of FSM Implicit Transitions. +; FsmImplicitTrans = 1 + +; List of file suffixes which will be read as SystemVerilog. White space +; in extensions can be specified with a back-slash: "\ ". Back-slashes +; can be specified with two consecutive back-slashes: "\\"; +; SVFileExtensions = sv svp svh + +; This setting is the same as the vlog -sv command line switch. +; Enables SystemVerilog features and keywords when true (1). +; When false (0), the rules of IEEE Std 1364-2001 are followed and +; SystemVerilog keywords are ignored. +; Svlog = 0 + +; Prints attribute placed upon SV packages during package import +; when true (1). The attribute will be ignored when this +; entry is false (0). The attribute name is "package_load_message". +; The value of this attribute is a string literal. +; Default is true (1). +; PrintSVPackageLoadingAttribute = 1 + +; Do not show immediate assertions with constant expressions in +; GUI/reports/UCDB etc. By default immediate assertions with constant +; expressions are shown in GUI/reports/UCDB etc. This does not affect +; evaluation of immediate assertions. +; ShowConstantImmediateAsserts = 0 + +; Controls if untyped parameters that are initialized with values greater +; than 2147483647 are mapped to generics of type INTEGER or ignored. +; If mapped to VHDL Integers, values greater than 2147483647 +; are mapped to negative values. +; Default is to map these parameter to generic of type INTEGER +; ForceUnsignedToVHDLInteger = 1 + +; Enable AMS wreal (wired real) extensions. Default is 0. +; WrealType = 1 + +; Controls SystemVerilog Language Extensions. These options enable +; some non-LRM compliant behavior. Valid extensions are "feci", +; "pae", "uslt" and "spsl". +; SVExtensions = uslt,spsl + +[sccom] +; Enable use of SCV include files and library. Default is off. +; UseScv = 1 + +; Add C++ compiler options to the sccom command line by using this variable. +; CppOptions = -g + +; Use custom C++ compiler located at this path rather than the default path. +; The path should point directly at a compiler executable. +; CppPath = /usr/bin/g++ + +; Enable verbose messages from sccom. Default is off. +; SccomVerbose = 1 + +; sccom logfile. Default is no logfile. +; SccomLogfile = sccom.log + +; Enable use of SC_MS include files and library. Default is off. +; UseScMs = 1 + +[vopt] +; Turn on code coverage in vopt. Default is off. +; Coverage = sbceft + +; Control compiler optimizations that are allowed when +; code coverage is on. Refer to the comment for this in the [vlog] area. +; CoverOpt = 3 + +; Increase or decrease the maximum number of rows allowed in a FEC table, implementing +; a condition coverage or expression coverage expression, by changing FecEffort. +; Higher FecEffort leads to a longer compile time, but more expressions covered. +; This is a number from 1 to 3, with the following meanings (the default is 1): +; 3 -- High FecEffort, Allows large expressions to be covered, will cause longer compile time. +; 2 -- Medium FecEffort, Allows more number of inputs per expression than Low FecEffort to be covered. +; 1 -- Low FecEffort, Covers only small expressions or conditions and skips larger ones. +; FecEffort = 2 + +; Enable code coverage reporting of code that has been optimized away. +; The default is not to report. +; CoverReportCancelled = 1 + +; Do not show immediate assertions with constant expressions in +; GUI/reports/UCDB etc. By default immediate assertions with constant +; expressions are shown in GUI/reports/UCDB etc. This does not affect +; evaluation of immediate assertions. +; ShowConstantImmediateAsserts = 0 + +; Set the maximum number of iterations permitted for a generate loop. +; Restricting this permits the implementation to recognize infinite +; generate loops. +; GenerateLoopIterationMax = 100000 + +; Set the maximum depth permitted for a recursive generate instantiation. +; Restricting this permits the implementation to recognize infinite +; recursions. +; GenerateRecursionDepthMax = 200 + +; Set the number of processes created during the code generation phase. +; By default a heuristic is used to set this value. This may be set to 0 +; to disable this feature completely. +; ParallelJobs = 0 + +; Controls SystemVerilog Language Extensions. These options enable +; some non-LRM compliant behavior. Valid extensions are "feci", +; "pae", "uslt" and "spsl". +; SVExtensions = uslt,spsl + +[vsim] +; vopt flow +; Set to turn on automatic optimization of a design. +; Default is on +VoptFlow = 1 + +; Simulator resolution +; Set to fs, ps, ns, us, ms, or sec with optional prefix of 1, 10, or 100. +Resolution = ns + +; Disable certain code coverage exclusions automatically. +; Assertions and FSM are exluded from the code coverage by default +; Set AutoExclusionsDisable = fsm to enable code coverage for fsm +; Set AutoExclusionsDisable = assertions to enable code coverage for assertions +; Set AutoExclusionsDisable = all to enable code coverage for all the automatic exclusions +; Or specify comma or space separated list +;AutoExclusionsDisable = fsm,assertions + +; User time unit for run commands +; Set to default, fs, ps, ns, us, ms, or sec. The default is to use the +; unit specified for Resolution. For example, if Resolution is 100ps, +; then UserTimeUnit defaults to ps. +; Should generally be set to default. +UserTimeUnit = default + +; Default run length +RunLength = 680 us + +; Maximum iterations that can be run without advancing simulation time +IterationLimit = 5000 + +; Control PSL and Verilog Assume directives during simulation +; Set SimulateAssumeDirectives = 0 to disable assume being simulated as asserts +; Set SimulateAssumeDirectives = 1 to enable assume simulation as asserts +; SimulateAssumeDirectives = 1 + +; Control the simulation of PSL and SVA +; These switches can be overridden by the vsim command line switches: +; -psl, -nopsl, -sva, -nosva. +; Set SimulatePSL = 0 to disable PSL simulation +; Set SimulatePSL = 1 to enable PSL simulation (default) +; SimulatePSL = 1 +; Set SimulateSVA = 0 to disable SVA simulation +; Set SimulateSVA = 1 to enable concurrent SVA simulation (default) +; SimulateSVA = 1 + +; Control SVA and VHDL immediate assertion directives during simulation +; Set SimulateImmedAsserts = 0 to disable simulation of immediate asserts +; Set SimulateImmedAsserts = 1 to enable simulation of immediate asserts +; SimulateImmedAsserts = 1 + +; Directives to license manager can be set either as single value or as +; space separated multi-values: +; vhdl Immediately reserve a VHDL license +; vlog Immediately reserve a Verilog license +; plus Immediately reserve a VHDL and Verilog license +; noqueue Do not wait in the license queue when a license is not available +; viewsim Try for viewer license but accept simulator license(s) instead +; of queuing for viewer license (PE ONLY) +; noviewer Disable checkout of msimviewer and vsim-viewer license +; features (PE ONLY) +; noslvhdl Disable checkout of qhsimvh and vsim license features +; noslvlog Disable checkout of qhsimvl and vsimvlog license features +; nomix Disable checkout of msimhdlmix and hdlmix license features +; nolnl Disable checkout of msimhdlsim and hdlsim license features +; mixedonly Disable checkout of qhsimvh,qhsimvl,vsim,vsimvlog license +; features +; lnlonly Disable checkout of qhsimvh,qhsimvl,vsim,vsimvlog,msimhdlmix, +; hdlmix license features +; Single value: +; License = plus +; Multi-value: +; License = noqueue plus + +; Severity level of a VHDL assertion message or of a SystemVerilog immediate assertion +; which will cause a running simulation to stop. +; VHDL assertions and SystemVerilog immediate assertions that occur with the +; given severity or higher will cause a running simulation to stop. +; This value is ignored during elaboration. +; 0 = Note 1 = Warning 2 = Error 3 = Failure 4 = Fatal +BreakOnAssertion = 3 + +; The class debug feature enables more visibility and tracking of class instances +; during simulation. By default this feature is 0 (disabled). To enable this +; feature set ClassDebug to 1. +; ClassDebug = 1 + +; Message Format conversion specifications: +; %S - Severity Level of message/assertion +; %R - Text of message +; %T - Time of message +; %D - Delta value (iteration number) of Time +; %K - Kind of path: Instance/Region/Signal/Process/Foreign Process/Unknown/Protected +; %i - Instance/Region/Signal pathname with Process name (if available) +; %I - shorthand for one of these: +; " %K: %i" +; " %K: %i File: %F" (when path is not Process or Signal) +; except that the %i in this case does not report the Process name +; %O - Process name +; %P - Instance/Region path without leaf process +; %F - File name +; %L - Line number; if assertion message, then line number of assertion or, if +; assertion is in a subprogram, line from which the call is made +; %u - Design unit name in form library.primary +; %U - Design unit name in form library.primary(secondary) +; %% - The '%' character itself +; +; If specific format for Severity Level is defined, use that format. +; Else, for a message that occurs during elaboration: +; -- Failure/Fatal message in VHDL region that is not a Process, and in +; certain non-VHDL regions, uses MessageFormatBreakLine; +; -- Failure/Fatal message otherwise uses MessageFormatBreak; +; -- Note/Warning/Error message uses MessageFormat. +; Else, for a message that occurs during runtime and triggers a breakpoint because +; of the BreakOnAssertion setting: +; -- if in a VHDL region that is not a Process, uses MessageFormatBreakLine; +; -- otherwise uses MessageFormatBreak. +; Else (a runtime message that does not trigger a breakpoint) uses MessageFormat. +; +; MessageFormatNote = "** %S: %R\n Time: %T Iteration: %D%I\n" +; MessageFormatWarning = "** %S: %R\n Time: %T Iteration: %D%I\n" +; MessageFormatError = "** %S: %R\n Time: %T Iteration: %D %K: %i File: %F\n" +; MessageFormatFail = "** %S: %R\n Time: %T Iteration: %D %K: %i File: %F\n" +; MessageFormatFatal = "** %S: %R\n Time: %T Iteration: %D %K: %i File: %F\n" +; MessageFormatBreakLine = "** %S: %R\n Time: %T Iteration: %D %K: %i File: %F Line: %L\n" +; MessageFormatBreak = "** %S: %R\n Time: %T Iteration: %D %K: %i File: %F\n" +; MessageFormat = "** %S: %R\n Time: %T Iteration: %D%I\n" + +; Error File - alternate file for storing error messages +; ErrorFile = error.log + +; Simulation Breakpoint messages +; This flag controls the display of function names when reporting the location +; where the simulator stops because of a breakpoint or fatal error. +; Example with function name: # Break in Process ctr at counter.vhd line 44 +; Example without function name: # Break at counter.vhd line 44 +; Default value is 1. +ShowFunctions = 1 + +; Default radix for all windows and commands. +; Radix may be one of: symbolic, ascii, binary, octal, decimal, hex, unsigned +; Flags may be one of: enumnumeric, showbase +DefaultRadix = symbolic +;DefaultRadixFlags = showbase + +; VSIM Startup command +; Startup = do startup.do + +; VSIM Shutdown file +; Filename to save u/i formats and configurations. +; ShutdownFile = restart.do +; To explicitly disable auto save: +; ShutdownFile = --disable-auto-save + +; File for saving command transcript +TranscriptFile = transcript + +; File for saving command history +; CommandHistory = cmdhist.log + +; Specify whether paths in simulator commands should be described +; in VHDL or Verilog format. +; For VHDL, PathSeparator = / +; For Verilog, PathSeparator = . +; Must not be the same character as DatasetSeparator. +PathSeparator = / + +; Specify the dataset separator for fully rooted contexts. +; The default is ':'. For example: sim:/top +; Must not be the same character as PathSeparator. +DatasetSeparator = : + +; Specify a unique path separator for the Signal Spy set of functions. +; The default will be to use the PathSeparator variable. +; Must not be the same character as DatasetSeparator. +; SignalSpyPathSeparator = / + +; Used to control parsing of HDL identifiers input to the tool. +; This includes CLI commands, vsim/vopt/vlog/vcom options, +; string arguments to FLI/VPI/DPI calls, etc. +; If set to 1, accept either Verilog escaped Id syntax or +; VHDL extended id syntax, regardless of source language. +; If set to 0, the syntax of the source language must be used. +; Each identifier in a hierarchical name may need different syntax, +; e.g. "/top/\vhdl*ext*id\/middle/\vlog*ext*id /bottom" or +; "top.\vhdl*ext*id\.middle.\vlog*ext*id .bottom" +; GenerousIdentifierParsing = 1 + +; Disable VHDL assertion messages +; IgnoreNote = 1 +; IgnoreWarning = 1 +; IgnoreError = 1 +; IgnoreFailure = 1 + +; Disable SystemVerilog assertion messages +; IgnoreSVAInfo = 1 +; IgnoreSVAWarning = 1 +; IgnoreSVAError = 1 +; IgnoreSVAFatal = 1 + +; Do not print any additional information from Severity System tasks. +; Only the message provided by the user is printed along with severity +; information. +; SVAPrintOnlyUserMessage = 1; + +; Default force kind. May be freeze, drive, deposit, or default +; or in other terms, fixed, wired, or charged. +; A value of "default" will use the signal kind to determine the +; force kind, drive for resolved signals, freeze for unresolved signals +; DefaultForceKind = freeze + +; Control the iteration of events when a VHDL signal is forced to a value +; This flag can be set to honour the signal update event in next iteration, +; the default is to update and propagate in the same iteration. +; ForceSigNextIter = 1 + + +; If zero, open files when elaborated; otherwise, open files on +; first read or write. Default is 0. +; DelayFileOpen = 1 + +; Control VHDL files opened for write. +; 0 = Buffered, 1 = Unbuffered +UnbufferedOutput = 0 + +; Control the number of VHDL files open concurrently. +; This number should always be less than the current ulimit +; setting for max file descriptors. +; 0 = unlimited +ConcurrentFileLimit = 40 + +; Control the number of hierarchical regions displayed as +; part of a signal name shown in the Wave window. +; A value of zero tells VSIM to display the full name. +; The default is 0. +; WaveSignalNameWidth = 0 + +; Turn off warnings when changing VHDL constants and generics +; Default is 1 to generate warning messages +; WarnConstantChange = 0 + +; Turn off warnings from accelerated versions of the std_logic_arith, +; std_logic_unsigned, and std_logic_signed packages. +; StdArithNoWarnings = 1 + +; Turn off warnings from accelerated versions of the IEEE numeric_std +; and numeric_bit packages. +; NumericStdNoWarnings = 1 + +; Use old-style (pre-6.6) VHDL FOR generate statement iteration names +; in the design hierarchy. +; This style is controlled by the value of the GenerateFormat +; value described next. Default is to use new-style names, which +; comprise the generate statement label, '(', the value of the generate +; parameter, and a closing ')'. +; Uncomment this to use old-style names. +; OldVhdlForGenNames = 1 + +; Control the format of the old-style VHDL FOR generate statement region +; name for each iteration. Do not quote it. +; The format string here must contain the conversion codes %s and %d, +; in that order, and no other conversion codes. The %s represents +; the generate statement label; the %d represents the generate parameter value +; at a particular iteration (this is the position number if the generate parameter +; is of an enumeration type). Embedded whitespace is allowed (but discouraged); +; leading and trailing whitespace is ignored. +; Application of the format must result in a unique region name over all +; loop iterations for a particular immediately enclosing scope so that name +; lookup can function properly. The default is %s__%d. +; GenerateFormat = %s__%d + +; Enable changes in VHDL elaboration to allow for Variable Logging +; This trades off simulation performance for the ability to log variables +; efficiently. By default this is disable for maximum simulation performance +; VhdlVariableLogging = 1 + +; Specify whether checkpoint files should be compressed. +; The default is 1 (compressed). +; CheckpointCompressMode = 0 + +; Specify gcc compiler used in the compilation of automatically generated DPI exportwrapper. +; Use custom gcc compiler located at this path rather than the default path. +; The path should point directly at a compiler executable. +; DpiCppPath = /bin/gcc + +; Specify whether to enable SystemVerilog DPI "out-of-the-blue" calls. +; The term "out-of-the-blue" refers to SystemVerilog export function calls +; made from C functions that don't have the proper context setup +; (as is the case when running under "DPI-C" import functions). +; When this is enabled, one can call a DPI export function +; (but not task) from any C code. +; the setting of this variable can be one of the following values: +; 0 : dpioutoftheblue call is disabled (default) +; 1 : dpioutoftheblue call is enabled, but export call debug support is not available. +; 2 : dpioutoftheblue call is enabled, and limited export call debug support is available. +; DpiOutOfTheBlue = 1 + +; Specify whether continuous assignments are run before other normal priority +; processes scheduled in the same iteration. This event ordering minimizes race +; differences between optimized and non-optimized designs, and is the default +; behavior beginning with the 6.5 release. For pre-6.5 event ordering, set +; ImmediateContinuousAssign to 0. +; The default is 1 (enabled). +; ImmediateContinuousAssign = 0 + +; List of dynamically loaded objects for Verilog PLI applications +; Veriuser = veriuser.sl + +; Which default VPI object model should the tool conform to? +; The 1364 modes are Verilog-only, for backwards compatibility with older +; libraries, and SystemVerilog objects are not available in these modes. +; +; In the absence of a user-specified default, the tool default is the +; latest available LRM behavior. +; Options for PliCompatDefault are: +; VPI_COMPATIBILITY_VERSION_1364v1995 +; VPI_COMPATIBILITY_VERSION_1364v2001 +; VPI_COMPATIBILITY_VERSION_1364v2005 +; VPI_COMPATIBILITY_VERSION_1800v2005 +; VPI_COMPATIBILITY_VERSION_1800v2008 +; +; Synonyms for each string are also recognized: +; VPI_COMPATIBILITY_VERSION_1364v1995 (1995, 95, 1364v1995, 1364V1995, VL1995) +; VPI_COMPATIBILITY_VERSION_1364v2001 (2001, 01, 1364v2001, 1364V2001, VL2001) +; VPI_COMPATIBILITY_VERSION_1364v2005 (1364v2005, 1364V2005, VL2005) +; VPI_COMPATIBILITY_VERSION_1800v2005 (2005, 05, 1800v2005, 1800V2005, SV2005) +; VPI_COMPATIBILITY_VERSION_1800v2008 (2008, 08, 1800v2008, 1800V2008, SV2008) + + +; PliCompatDefault = VPI_COMPATIBILITY_VERSION_1800v2005 + +; Specify whether the Verilog system task $fopen or vpi_mcd_open() +; will create directories that do not exist when opening the file +; in "a" or "w" mode. +; The default is 0 (do not create non-existent directories) +; CreateDirForFileAccess = 1 + +; Specify default options for the restart command. Options can be one +; or more of: -force -nobreakpoint -nolist -nolog -nowave -noassertions +; DefaultRestartOptions = -force + + +; Specify default UVM-aware debug options if the vsim -uvmcontrol switch is not used. +; Valid options include: all, none, verbose, disable, struct, msglog, trlog, certe. +; Options can be enabled by just adding the name, or disabled by prefixing the option with a "-". +; The list of options must be delimited by commas, without spaces or tabs. +; The default is UVMControl = struct + +; Some examples +; To turn on all available UVM-aware debug features: +; UVMControl = all +; To turn on the struct window, mesage logging, and transaction logging: +; UVMControl = struct,msglog,trlog +; To turn on all options except certe: +; UVMControl = all,-certe +; To completely disable all UVM-aware debug functionality: +; UVMControl = disable + + +; Turn on (1) or off (0) WLF file compression. +; The default is 1 (compress WLF file). +; WLFCompress = 0 + +; Specify whether to save all design hierarchy (1) in the WLF file +; or only regions containing logged signals (0). +; The default is 0 (save only regions with logged signals). +; WLFSaveAllRegions = 1 + +; WLF file time limit. Limit WLF file by time, as closely as possible, +; to the specified amount of simulation time. When the limit is exceeded +; the earliest times get truncated from the file. +; If both time and size limits are specified the most restrictive is used. +; UserTimeUnits are used if time units are not specified. +; The default is 0 (no limit). Example: WLFTimeLimit = {100 ms} +; WLFTimeLimit = 0 + +; WLF file size limit. Limit WLF file size, as closely as possible, +; to the specified number of megabytes. If both time and size limits +; are specified then the most restrictive is used. +; The default is 0 (no limit). +; WLFSizeLimit = 1000 + +; Specify whether or not a WLF file should be deleted when the +; simulation ends. A value of 1 will cause the WLF file to be deleted. +; The default is 0 (do not delete WLF file when simulation ends). +; WLFDeleteOnQuit = 1 + +; Specify whether or not a WLF file should be optimized during +; simulation. If set to 0, the WLF file will not be optimized. +; The default is 1, optimize the WLF file. +; WLFOptimize = 0 + +; Specify the name of the WLF file. +; The default is vsim.wlf +; WLFFilename = vsim.wlf + +; Specify whether to lock the WLF file. +; Locking the file prevents other invocations of ModelSim/Questa tools from +; inadvertently overwriting the WLF file. +; The default is 1, lock the WLF file. +; WLFFileLock = 0 + +; Specify the update interval for the WLF file. +; Value is the number of seconds between updated. After at least the +; interval number of seconds, the wlf file is flushed, ensuring that the data +; is correct when viewed from a separate live viewer. Setting to 0 means no +; updating. Default is 10 seconds, which has a tiny performance impact +; WLFUpdateInterval = 10 + +; Specify the WLF reader cache size limit for each open WLF file. +; The size is giving in megabytes. A value of 0 turns off the +; WLF cache. +; WLFSimCacheSize allows a different cache size to be set for +; simulation WLF file independent of post-simulation WLF file +; viewing. If WLFSimCacheSize is not set it defaults to the +; WLFCacheSize setting. +; The default WLFCacheSize setting is enabled to 2000M per open WLF file on most +; platforms; on Windows, the setting is 1000M to help avoid filling process memory. +; WLFCacheSize = 2000 +; WLFSimCacheSize = 500 + +; Specify the WLF file event collapse mode. +; 0 = Preserve all events and event order. (same as -wlfnocollapse) +; 1 = Only record values of logged objects at the end of a simulator iteration. +; (same as -wlfcollapsedelta) +; 2 = Only record values of logged objects at the end of a simulator time step. +; (same as -wlfcollapsetime) +; The default is 1. +; WLFCollapseMode = 0 + +; Specify whether WLF file logging can use threads on multi-processor machines +; if 0, no threads will be used, if 1, threads will be used if the system has +; more than one processor +; WLFUseThreads = 1 + +; Specify the relative size of logged objects that will trigger "large object" +; messages at log/wave/list time. This size value is an approximation of +; the number of bytes needed to store the value of the object before compression +; and optimization. +; The default LargeObjectSize size is 500k +; LargeObjectSize = 500000 + +; Specify whether to output "large object" warning messages. +; The default is 0 which means the warning messages will come out. +; LargeObjectSilent = 0 + +; Turn on/off undebuggable SystemC type warnings. Default is on. +; ShowUndebuggableScTypeWarning = 0 + +; Turn on/off unassociated SystemC name warnings. Default is off. +; ShowUnassociatedScNameWarning = 1 + +; Turn on/off SystemC IEEE 1666 deprecation warnings. Default is off. +; ScShowIeeeDeprecationWarnings = 1 + +; Turn on/off the check for multiple drivers on a SystemC sc_signal. Default is off. +; ScEnableScSignalWriteCheck = 1 + +; Set SystemC default time unit. +; Set to fs, ps, ns, us, ms, or sec with optional +; prefix of 1, 10, or 100. The default is 1 ns. +; The ScTimeUnit value is honored if it is coarser than Resolution. +; If ScTimeUnit is finer than Resolution, it is set to the value +; of Resolution. For example, if Resolution is 100ps and ScTimeUnit is ns, +; then the default time unit will be 1 ns. However if Resolution +; is 10 ns and ScTimeUnit is ns, then the default time unit will be 10 ns. +ScTimeUnit = ns + +; Set SystemC sc_main stack size. The stack size is set as an integer +; number followed by the unit which can be Kb(Kilo-byte), Mb(Mega-byte) or +; Gb(Giga-byte). Default is 10 Mb. The stack size for sc_main depends +; on the amount of data on the sc_main() stack and the memory required +; to succesfully execute the longest function call chain of sc_main(). +ScMainStackSize = 10 Mb + +; Turn on/off execution of remainder of sc_main upon quitting the current +; simulation session. If the cumulative length of sc_main() in terms of +; simulation time units is less than the length of the current simulation +; run upon quit or restart, sc_main() will be in the middle of execution. +; This switch gives the option to execute the remainder of sc_main upon +; quitting simulation. The drawback of not running sc_main till the end +; is memory leaks for objects created by sc_main. If on, the remainder of +; sc_main will be executed ignoring all delays. This may cause the simulator +; to crash if the code in sc_main is dependent on some simulation state. +; Default is on. +ScMainFinishOnQuit = 1 + +; Set the SCV relationship name that will be used to identify phase +; relations. If the name given to a transactor relation matches this +; name, the transactions involved will be treated as phase transactions +ScvPhaseRelationName = mti_phase + +; Customize the vsim kernel shutdown behavior at the end of the simulation. +; Some common causes of the end of simulation are $finish (implicit or explicit), +; sc_stop(), tf_dofinish(), and assertion failures. +; This should be set to "ask", "exit", or "stop". The default is "ask". +; "ask" -- In batch mode, the vsim kernel will abruptly exit. +; In GUI mode, a dialog box will pop up and ask for user confirmation +; whether or not to quit the simulation. +; "stop" -- Cause the simulation to stay loaded in memory. This can make some +; post-simulation tasks easier. +; "exit" -- The simulation will abruptly exit without asking for any confirmation. +; "final" -- Run SystemVerilog final blocks then behave as "stop". +; Note: This variable can be overridden with the vsim "-onfinish" command line switch. +OnFinish = ask + +; Print pending deferred assertion messages. +; Deferred assertion messages may be scheduled after the $finish in the same +; time step. Deferred assertions scheduled to print after the $finish are +; printed before exiting with severity level NOTE since it's not known whether +; the assertion is still valid due to being printed in the active region +; instead of the reactive region where they are normally printed. +; OnFinishPendingAssert = 1; + +; Print "simstats" result +; 0 == do not print simstats +; 1 == print at end of simulation +; 2 == print at end of run +; 3 == print at end of run and end of simulation +; default == 0 +; PrintSimStats = 1 + + +; Assertion File - alternate file for storing VHDL/PSL/Verilog assertion messages +; AssertFile = assert.log + +; Enable assertion counts. Default is off. +; AssertionCover = 1 + +; Run simulator in assertion debug mode. Default is off. +; AssertionDebug = 1 + +; Turn on/off PSL/SVA/VHDL assertion enable. Default is on. +; AssertionEnable = 0 + +; Set PSL/SVA/VHDL concurrent assertion fail limit. Default is -1. +; Any positive integer, -1 for infinity. +; AssertionLimit = 1 + +; Turn on/off concurrent assertion pass log. Default is off. +; Assertion pass logging is only enabled when assertion is browseable +; and assertion debug is enabled. +; AssertionPassLog = 1 + +; Turn on/off PSL concurrent assertion fail log. Default is on. +; The flag does not affect SVA +; AssertionFailLog = 0 + +; Turn on/off SVA concurrent assertion local var printing in -assertdebug mode. Default is on. +; AssertionFailLocalVarLog = 0 + +; Set action type for PSL/SVA concurrent assertion fail action. Default is continue. +; 0 = Continue 1 = Break 2 = Exit +; AssertionFailAction = 1 + +; Enable the active thread monitor in the waveform display when assertion debug is enabled. +; AssertionActiveThreadMonitor = 1 + +; Control how many waveform rows will be used for displaying the active threads. Default is 5. +; AssertionActiveThreadMonitorLimit = 5 + +; Assertion thread limit after which assertion would be killed/switched off. +; The default is -1 (unlimited). If the number of threads for an assertion go +; beyond this limit, the assertion would be either switched off or killed. This +; limit applies to only assert directives. +;AssertionThreadLimit = -1 + +; Action to be taken once the assertion thread limit is reached. Default +; is kill. It can have a value of off or kill. In case of kill, all the existing +; threads are terminated and no new attempts are started. In case of off, the +; existing attempts keep on evaluating but no new attempts are started. This +; variable applies to only assert directives. +;AssertionThreadLimitAction = kill + +; Cover thread limit after which cover would be killed/switched off. +; The default is -1 (unlimited). If the number of threads for a cover go +; beyond this limit, the cover would be either switched off or killed. This +; limit applies to only cover directives. +;CoverThreadLimit = -1 + +; Action to be taken once the cover thread limit is reached. Default +; is kill. It can have a value of off or kill. In case of kill, all the existing +; threads are terminated and no new attempts are started. In case of off, the +; existing attempts keep on evaluating but no new attempts are started. This +; variable applies to only cover directives. +;CoverThreadLimitAction = kill + + +; By default immediate assertions do not participate in Assertion Coverage calculations +; unless they are executed. This switch causes all immediate assertions in the design +; to participate in Assertion Coverage calculations, whether attempted or not. +; UnattemptedImmediateAssertions = 0 + +; By default immediate covers participate in Coverage calculations +; whether they are attempted or not. This switch causes all unattempted +; immediate covers in the design to stop participating in Coverage +; calculations. +; UnattemptedImmediateCovers = 0 + +; By default pass action block is not executed for assertions on vacuous +; success. The following variable is provided to enable execution of +; pass action block on vacuous success. The following variable is only effective +; if the user does not disable pass action block execution by using either +; system tasks or CLI. Also there is a performance penalty for enabling +; the following variable. +;AssertionEnableVacuousPassActionBlock = 1 + +; As per strict 1850-2005 PSL LRM, an always property can either pass +; or fail. However, by default, Questa reports multiple passes and +; multiple fails on top always/never property (always/never operator +; is the top operator under Verification Directive). The reason +; being that Questa reports passes and fails on per attempt of the +; top always/never property. Use the following flag to instruct +; Questa to strictly follow LRM. With this flag, all assert/never +; directives will start an attempt once at start of simulation. +; The attempt can either fail, match or match vacuously. +; For e.g. if always is the top operator under assert, the always will +; keep on checking the property at every clock. If the property under +; always fails, the directive will be considered failed and no more +; checking will be done for that directive. A top always property, +; if it does not fail, will show a pass at end of simulation. +; The default value is '0' (i.e. zero is off). For example: +; PslOneAttempt = 1 + +; Specify the number of clock ticks to represent infinite clock ticks. +; This affects eventually!, until! and until_!. If at End of Simulation +; (EOS) an active strong-property has not clocked this number of +; clock ticks then neither pass or fail (vacuous match) is returned +; else respective fail/pass is returned. The default value is '0' (zero) +; which effectively does not check for clock tick condition. For example: +; PslInfinityThreshold = 5000 + +; Control how many thread start times will be preserved for ATV viewing for a given assertion +; instance. Default is -1 (ALL). +; ATVStartTimeKeepCount = -1 + +; Turn on/off code coverage +; CodeCoverage = 0 + +; Count all code coverage condition and expression truth table rows that match. +; CoverCountAll = 1 + +; Turn off automatic inclusion of VHDL integers in toggle coverage. Default +; is to include them. +; ToggleNoIntegers = 1 + +; Set the maximum number of values that are collected for toggle coverage of +; VHDL integers. Default is 100; +; ToggleMaxIntValues = 100 + +; Set the maximum number of values that are collected for toggle coverage of +; Verilog real. Default is 100; +; ToggleMaxRealValues = 100 + +; Turn on automatic inclusion of Verilog integers in toggle coverage, except +; for enumeration types. Default is to include them. +; ToggleVlogIntegers = 0 + +; Turn on automatic inclusion of Verilog real type in toggle coverage, except +; for shortreal types. Default is to not include them. +; ToggleVlogReal = 1 + +; Turn on automatic inclusion of Verilog fixed-size unpacked arrays, VHDL multi-d arrays +; and VHDL arrays-of-arrays in toggle coverage. +; Default is to not include them. +; ToggleFixedSizeArray = 1 + +; Increase or decrease the maximum size of Verilog unpacked fixed-size arrays, +; VHDL multi-d arrays and VHDL arrays-of-arrays that are included for toggle coverage. +; This leads to a longer simulation time with bigger arrays covered with toggle coverage. +; Default is 1024. +; ToggleMaxFixedSizeArray = 1024 + +; Treat Verilog multi-dimensional packed vectors and packed structures as equivalently sized +; one-dimensional packed vectors for toggle coverage. Default is 0. +; TogglePackedAsVec = 0 + +; Treat Verilog enumerated types as equivalently sized one-dimensional packed vectors for +; toggle coverage. Default is 0. +; ToggleVlogEnumBits = 0 + +; Turn off automatic inclusion of VHDL records in toggle coverage. +; Default is to include them. +; ToggleVHDLRecords = 0 + +; Limit the widths of registers automatically tracked for toggle coverage. Default is 128. +; For unlimited width, set to 0. +; ToggleWidthLimit = 128 + +; Limit the counts that are tracked for toggle coverage. When all edges for a bit have +; reached this count, further activity on the bit is ignored. Default is 1. +; For unlimited counts, set to 0. +; ToggleCountLimit = 1 + +; Change the mode of extended toggle coverage. Default is 3. Valid modes are 1, 2 and 3. +; Following is the toggle coverage calculation criteria based on extended toggle mode: +; Mode 1: 0L->1H & 1H->0L & any one 'Z' transition (to/from 'Z'). +; Mode 2: 0L->1H & 1H->0L & one transition to 'Z' & one transition from 'Z'. +; Mode 3: 0L->1H & 1H->0L & all 'Z' transitions. +; ExtendedToggleMode = 3 + +; Enable toggle statistics collection only for ports. Default is 0. +; TogglePortsOnly = 1 + +; Turn on/off all PSL/SVA cover directive enables. Default is on. +; CoverEnable = 0 + +; Turn on/off PSL/SVA cover log. Default is off "0". +; CoverLog = 1 + +; Set "at_least" value for all PSL/SVA cover directives. Default is 1. +; CoverAtLeast = 2 + +; Set "limit" value for all PSL/SVA cover directives. Default is -1. +; Any positive integer, -1 for infinity. +; CoverLimit = 1 + +; Specify the coverage database filename. +; Default is "" (i.e. database is NOT automatically saved on close). +; UCDBFilename = vsim.ucdb + +; Specify the maximum limit for the number of Cross (bin) products reported +; in XML and UCDB report against a Cross. A warning is issued if the limit +; is crossed. Default is zero. vsim switch -cvgmaxrptrhscross can override this +; setting. +; MaxReportRhsSVCrossProducts = 1000 + +; Specify the override for the "auto_bin_max" option for the Covergroups. +; If not specified then value from Covergroup "option" is used. +; SVCoverpointAutoBinMax = 64 + +; Specify the override for the value of "cross_num_print_missing" +; option for the Cross in Covergroups. If not specified then value +; specified in the "option.cross_num_print_missing" is used. This +; is a runtime option. NOTE: This overrides any "cross_num_print_missing" +; value specified by user in source file and any SVCrossNumPrintMissingDefault +; specified in modelsim.ini. +; SVCrossNumPrintMissing = 0 + +; Specify whether to use the value of "cross_num_print_missing" +; option in report and GUI for the Cross in Covergroups. If not specified then +; cross_num_print_missing is ignored for creating reports and displaying +; covergroups in GUI. Default is 0, which means ignore "cross_num_print_missing". +; UseSVCrossNumPrintMissing = 0 + +; Specify the threshold of Coverpoint wildcard bin value range size, above which +; a warning will be triggered. The default is 4K -- 12 wildcard bits. +; SVCoverpointWildCardBinValueSizeWarn = 4096 + +; Specify the override for the value of "strobe" option for the +; Covergroup Type. If not specified then value in "type_option.strobe" +; will be used. This is runtime option which forces "strobe" to +; user specified value and supersedes user specified values in the +; SystemVerilog Code. NOTE: This also overrides the compile time +; default value override specified using "SVCovergroupStrobeDefault" +; SVCovergroupStrobe = 0 + +; Override for explicit assignments in source code to "option.goal" of +; SystemVerilog covergroup, coverpoint, and cross. It also overrides the +; default value of "option.goal" (defined to be 100 in the SystemVerilog +; LRM) and the value of modelsim.ini variable "SVCovergroupGoalDefault". +; SVCovergroupGoal = 100 + +; Override for explicit assignments in source code to "type_option.goal" of +; SystemVerilog covergroup, coverpoint, and cross. It also overrides the +; default value of "type_option.goal" (defined to be 100 in the SystemVerilog +; LRM) and the value of modelsim.ini variable "SVCovergroupTypeGoalDefault". +; SVCovergroupTypeGoal = 100 + +; Enforce the 6.3 behavior of covergroup get_coverage() and get_inst_coverage() +; builtin functions, and report. This setting changes the default values of +; option.get_inst_coverage and type_option.merge_instances to ensure the 6.3 +; behavior if explicit assignments are not made on option.get_inst_coverage and +; type_option.merge_instances by the user. There are two vsim command line +; options, -cvg63 and -nocvg63 to override this setting from vsim command line. +; The default value of this variable from release 6.6 onwards is 0. This default +; drives compliance with the clarified behavior in the IEEE 1800-2009 standard. +; SVCovergroup63Compatibility = 0 + +; Enforce the 6.5 default behavior of covergroup get_coverage() builtin +; functions, GUI, and report. This setting changes the default values of +; type_option.merge_instances to ensure the 6.5 default behavior if explicit +; assignments are not made on type_option.merge_instances by the user. +; There are two vsim command line options, -cvgmergeinstances and +; -nocvgmergeinstances to override this setting from vsim command line. +; The default value of this variable from release 6.6 onwards is 0. This default +; drives compliance with the clarified behavior in the IEEE 1800-2009 standard. +; SvCovergroupMergeInstancesDefault = 1 + +; Enable or disable generation of more detailed information about the sampling +; of covergroup, cross, and coverpoints. It provides the details of the number +; of times the covergroup instance and type were sampled, as well as details +; about why covergroup, cross and coverpoint were not covered. A non-zero value +; is to enable this feature. 0 is to disable this feature. Default is 0 +; SVCovergroupSampleInfo = 0 + +; Specify the maximum number of Coverpoint bins in whole design for +; all Covergroups. +; MaxSVCoverpointBinsDesign = 2147483648 + +; Specify maximum number of Coverpoint bins in any instance of a Covergroup +; MaxSVCoverpointBinsInst = 2147483648 + +; Specify the maximum number of Cross bins in whole design for +; all Covergroups. +; MaxSVCrossBinsDesign = 2147483648 + +; Specify maximum number of Cross bins in any instance of a Covergroup +; MaxSVCrossBinsInst = 2147483648 + +; Specify whether vsim will collect the coverage data of zero-weight coverage items or not. +; By default, this variable is set 0, in which case option.no_collect setting will take effect. +; If this variable is set to 1, all zero-weight coverage items will not be saved. +; Note that the usage of vsim switch -cvgzwnocollect, if present, will override the setting +; of this variable. +; CvgZWNoCollect = 1 + +; Specify a space delimited list of double quoted TCL style +; regular expressions which will be matched against the text of all messages. +; If any regular expression is found to be contained within any message, the +; status for that message will not be propagated to the UCDB TESTSTATUS. +; If no match is detected, then the status will be propagated to the +; UCDB TESTSTATUS. More than one such regular expression text is allowed, +; and each message text is compared for each regular expression in the list. +; UCDBTestStatusMessageFilter = "Done with Test Bench" "Ignore .* message" + +; Set weight for all PSL/SVA cover directives. Default is 1. +; CoverWeight = 2 + +; Check vsim plusargs. Default is 0 (off). +; 0 = Don't check plusargs +; 1 = Warning on unrecognized plusarg +; 2 = Error and exit on unrecognized plusarg +; CheckPlusargs = 1 + +; Load the specified shared objects with the RTLD_GLOBAL flag. +; This gives global visibility to all symbols in the shared objects, +; meaning that subsequently loaded shared objects can bind to symbols +; in the global shared objects. The list of shared objects should +; be whitespace delimited. This option is not supported on the +; Windows or AIX platforms. +; GlobalSharedObjectList = example1.so example2.so example3.so + +; Run the 0in tools from within the simulator. +; Default is off. +; ZeroIn = 1 + +; Set the options to be passed to the 0in runtime tool. +; Default value set to "". +; ZeroInOptions = "" + +; Initial seed for the random number generator of the root thread (SystemVerilog). +; NOTE: This variable can be overridden with the vsim "-sv_seed" command line switch. +; The default value is 0. +; Sv_Seed = 0 + +; Specify the solver "engine" that vsim will select for constrained random +; generation. +; Valid values are: +; "auto" - automatically select the best engine for the current +; constraint scenario +; "bdd" - evaluate all constraint scenarios using the BDD solver engine +; "act" - evaluate all constraint scenarios using the ACT solver engine +; While the BDD solver engine is generally efficient with constraint scenarios +; involving bitwise logical relationships, the ACT solver engine can exhibit +; superior performance with constraint scenarios involving large numbers of +; random variables related via arithmetic operators (+, *, etc). +; NOTE: This variable can be overridden with the vsim "-solveengine" command +; line switch. +; The default value is "auto". +; SolveEngine = auto + +; Specify if the solver should attempt to ignore overflow/underflow semantics +; for arithmetic constraints (multiply, addition, subtraction) in order to +; improve performance. The "solveignoreoverflow" attribute can be specified on +; a per-call basis to randomize() to override this setting. +; The default value is 0 (overflow/underflow is not ignored). Set to 1 to +; ignore overflow/underflow. +; SolveIgnoreOverflow = 0 + +; Specifies the maximum size that a dynamic array may be resized to by the +; solver. If the solver attempts to resize a dynamic array to a size greater +; than the specified limit, the solver will abort with an error. +; The default value is 2000. A value of 0 indicates no limit. +; SolveArrayResizeMax = 2000 + +; Error message severity when randomize() failure is detected (SystemVerilog). +; 0 = No error 1 = Warning 2 = Error 3 = Failure 4 = Fatal +; The default is 0 (no error). +; SolveFailSeverity = 0 + +; Enable/disable debug information for randomize() failures. +; NOTE: This variable can be overridden with the vsim "-solvefaildbug" command +; line switch. +; The default is 0 (disabled). Set to 1 to enable. +; SolveFailDebug = 0 + +; Specify the maximum size of the solution graph generated by the BDD solver. +; This value can be used to force the BDD solver to abort the evaluation of a +; complex constraint scenario that cannot be evaluated with finite memory. +; This value is specified in 1000s of nodes. +; The default value is 10000. A value of 0 indicates no limit. +; SolveGraphMaxSize = 10000 + +; Specify the maximum number of evaluations that may be performed on the +; solution graph by the BDD solver. This value can be used to force the BDD +; solver to abort the evaluation of a complex constraint scenario that cannot +; be evaluated in finite time. This value is specified in 10000s of evaluations. +; The default value is 10000. A value of 0 indicates no limit. +; SolveGraphMaxEval = 10000 + +; Specify the maximum number of tests that the ACT solver may evaluate before +; abandoning an attempt to solve a particular constraint scenario. +; The default value is 2000000. A value of 0 indicates no limit. +; SolveACTMaxTests = 2000000 + +; Specify the maximum number of operations that the ACT solver may perform +; before abandoning an attempt to solve a particular constraint scenario. The +; value is specified in 1000000s of operations. +; The default value is 10000. A value of 0 indicates no limit. +; SolveACTMaxOps = 10000 + +; Specify the number of times the ACT solver will retry to evaluate a constraint +; scenario that fails due to the SolveACTMaxTests threshold. +; The default value is 0 (no retry). +; SolveACTRetryCount = 0 + +; SolveSpeculateLevel controls whether or not the solver performs speculation +; during the evaluation of a constraint scenario. +; Speculation is an attempt to partition complex constraint scenarios by +; choosing a 'speculation' subset of the variables and constraints. This +; 'speculation' set is solved independently of the remaining constraints. +; The solver then attempts to solve the remaining variables and constraints +; (the 'dependent' set). If this attempt fails, the solver backs up and +; re-solves the 'speculation' set, then retries the 'dependent' set. +; Valid values are: +; 0 - no speculation +; 1 - enable speculation that maintains LRM specified distribution +; 2 - enable other speculation - may yield non-LRM distribution +; Currently, distribution constraints and solve-before constraints are +; used in selecting the 'speculation' sets for speculation level 1. Non-LRM +; compliant speculation includes random variables in condition expressions. +; The default value is 0. +; SolveSpeculateLevel = 0 + +; By default, when speculation is enabled, the solver first tries to solve a +; constraint scenario *without* speculation. If the solver fails to evaluate +; the constraint scenario (due to time/memory limits) then the solver will +; re-evaluate the constraint scenario with speculation. If SolveSpeculateFirst +; is set to 1, the solver will skip the initial non-speculative attempt to +; evaluate the constraint scenario. (Only applies when SolveSpeculateLevel is +; non-zero) +; The default value is 0. +; SolveSpeculateFirst = 0 + +; Specify the maximum bit width of a variable in a conditional expression that +; may be considered as the basis for "conditional" speculation. (Only applies +; when SolveSpeculateLevel=2) +; The default value is 6. +; SolveSpeculateMaxCondWidth = 6 + +; Specify the maximum number of attempts to solve a speculative set of random +; variables and constraints. Exceeding this limit will cause the solver to +; abandon the current speculative set. (Only applies when SolveSpeculateLevel +; is non-zero) +; The default value is 100. +; SolveSpeculateMaxIterations = 100 + +; Specifies whether to attempt speculation on solve-before constraints or +; distribution constraints first. A value of 0 specifies that solve-before +; constraints are attempted first as the basis for speculative randomization. +; A value of 1 specifies that distribution constraints are attempted first +; as the basis for speculative randomization. +; The default value is 0. +; SolveSpeculateDistFirst = 0 + +; If the non-speculative BDD solver fails to evaluate a constraint scenario +; (due to time/memory limits) then the solver can be instructed to automatically +; re-evaluate the constraint scenario with the ACT solver engine. Set +; SolveACTbeforeSpeculate to 1 to enable this feature. +; The default value is 0 (do not re-evaluate with the ACT solver). +; SolveACTbeforeSpeculate = 0 + +; Use SolveFlags to specify options that will guide the behavior of the +; constraint solver. These options may improve the performance of the +; constraint solver for some testcases, and decrease the performance of the +; constraint solver for others. +; Valid flags are: +; i = disable bit interleaving for >, >=, <, <= constraints (BDD engine) +; n = disable bit interleaving for all constraints (BDD engine) +; r = reverse bit interleaving (BDD engine) +; The default value is "" (no options). +; SolveFlags = + +; Specify random sequence compatiblity with a prior letter release. This +; option is used to get the same random sequences during simulation as +; as a prior letter release. Only prior letter releases (of the current +; number release) are allowed. +; NOTE: Only those random sequence changes due to solver optimizations are +; reverted by this variable. Random sequence changes due to solver bugfixes +; cannot be un-done. +; NOTE: This variable can be overridden with the vsim "-solverev" command +; line switch. +; Default value set to "" (no compatibility). +; SolveRev = + +; Environment variable expansion of command line arguments has been depricated +; in favor shell level expansion. Universal environment variable expansion +; inside -f files is support and continued support for MGC Location Maps provide +; alternative methods for handling flexible pathnames. +; The following line may be uncommented and the value set to 1 to re-enable this +; deprecated behavior. The default value is 0. +; DeprecatedEnvironmentVariableExpansion = 0 + +; Turn on/off collapsing of bus ports in VCD dumpports output +DumpportsCollapse = 1 + +; Location of Multi-Level Verification Component (MVC) installation. +; The default location is the product installation directory. +MvcHome = $MODEL_TECH/.. + +; Initialize SystemVerilog enums using the base type's default value +; instead of the leftmost value. +; EnumBaseInit = 1 + +; Suppress file type registration. +; SuppressFileTypeReg = 1 + +; Controls SystemVerilog Language Extensions. These options enable +; some non-LRM compliant behavior. Valid extensions are "feci", +; "pae", "uslt" and "spsl". +; SVExtensions = uslt,spsl + +[lmc] +; The simulator's interface to Logic Modeling's SmartModel SWIFT software +libsm = $MODEL_TECH/libsm.sl +; The simulator's interface to Logic Modeling's SmartModel SWIFT software (Windows NT) +; libsm = $MODEL_TECH/libsm.dll +; Logic Modeling's SmartModel SWIFT software (HP 9000 Series 700) +; libswift = $LMC_HOME/lib/hp700.lib/libswift.sl +; Logic Modeling's SmartModel SWIFT software (IBM RISC System/6000) +; libswift = $LMC_HOME/lib/ibmrs.lib/swift.o +; Logic Modeling's SmartModel SWIFT software (Sun4 Solaris) +; libswift = $LMC_HOME/lib/sun4Solaris.lib/libswift.so +; Logic Modeling's SmartModel SWIFT software (Windows NT) +; libswift = $LMC_HOME/lib/pcnt.lib/libswift.dll +; Logic Modeling's SmartModel SWIFT software (non-Enterprise versions of Linux) +; libswift = $LMC_HOME/lib/x86_linux.lib/libswift.so +; Logic Modeling's SmartModel SWIFT software (Enterprise versions of Linux) +; libswift = $LMC_HOME/lib/linux.lib/libswift.so + +; The simulator's interface to Logic Modeling's hardware modeler SFI software +libhm = $MODEL_TECH/libhm.sl +; The simulator's interface to Logic Modeling's hardware modeler SFI software (Windows NT) +; libhm = $MODEL_TECH/libhm.dll +; Logic Modeling's hardware modeler SFI software (HP 9000 Series 700) +; libsfi = /lib/hp700/libsfi.sl +; Logic Modeling's hardware modeler SFI software (IBM RISC System/6000) +; libsfi = /lib/rs6000/libsfi.a +; Logic Modeling's hardware modeler SFI software (Sun4 Solaris) +; libsfi = /lib/sun4.solaris/libsfi.so +; Logic Modeling's hardware modeler SFI software (Windows NT) +; libsfi = /lib/pcnt/lm_sfi.dll +; Logic Modeling's hardware modeler SFI software (Linux) +; libsfi = /lib/linux/libsfi.so + +[msg_system] +; Change a message severity or suppress a message. +; The format is: = [,...] +; suppress can be used to achieve +nowarn functionality +; The format is: suppress = ,,[,,...] +; Examples: +suppress = 8780 ;an explanation can be had by running: verror 8780 +; note = 3009 +; warning = 3033 +; error = 3010,3016 +; fatal = 3016,3033 +; suppress = 3009,3016,3043 +; suppress = 3009,CNNODP,3043,TFMPC +; suppress = 8683,8684 +; The command verror can be used to get the complete +; description of a message. + +; Control transcripting of Verilog display system task messages and +; PLI/FLI print function call messages. The system tasks include +; $display[bho], $strobe[bho], $monitor[bho], and $write[bho]. They +; also include the analogous file I/O tasks that write to STDOUT +; (i.e. $fwrite or $fdisplay). The PLI/FLI calls include io_printf, +; vpi_printf, mti_PrintMessage, and mti_PrintFormatted. The default +; is to have messages appear only in the transcript. The other +; settings are to send messages to the wlf file only (messages that +; are recorded in the wlf file can be viewed in the MsgViewer) or +; to both the transcript and the wlf file. The valid values are +; tran {transcript only (default)} +; wlf {wlf file only} +; both {transcript and wlf file} +; displaymsgmode = tran + +; Control transcripting of elaboration/runtime messages not +; addressed by the displaymsgmode setting. The default is to +; have messages appear only in the transcript. The other settings +; are to send messages to the wlf file only (messages that are +; recorded in the wlf file can be viewed in the MsgViewer) or to both +; the transcript and the wlf file. The valid values are +; tran {transcript only (default)} +; wlf {wlf file only} +; both {transcript and wlf file} +; msgmode = tran +[Project] +; Warning -- Do not edit the project properties directly. +; Property names are dynamic in nature and property +; values have special syntax. Changing property data directly +; can result in a corrupt MPF file. All project properties +; can be modified through project window dialogs. +Project_Version = 6 +Project_DefaultLib = work +Project_SortMethod = unused +Project_Files_Count = 5 +Project_File_0 = /local/trb/git/trbnet/lattice/ecp3/fifo/fifo_2x64k_oreg.vhd +Project_File_P_0 = vhdl_novitalcheck 0 file_type vhdl group_id 0 cover_nofec 0 vhdl_nodebug 0 vhdl_1164 1 vhdl_noload 0 vhdl_synth 0 vhdl_enable0In 0 folder {Top Level} last_compile 1703012791 vhdl_disableopt 0 cover_excludedefault 0 vhdl_vital 0 vhdl_warn1 1 vhdl_showsource 0 vhdl_explicit 1 vhdl_warn2 1 vhdl_0InOptions {} cover_covercells 0 vhdl_warn3 1 vhdl_options {} cover_optlevel 3 voptflow 1 vhdl_warn4 1 ood 0 toggle - vhdl_warn5 1 compile_to work cover_noshort 0 compile_order 3 dont_compile 0 cover_nosub 0 vhdl_use93 2002 +Project_File_1 = /local/trb/git/trbnet/trb_net_std.vhd +Project_File_P_1 = vhdl_novitalcheck 0 file_type vhdl group_id 0 cover_nofec 0 vhdl_nodebug 0 vhdl_1164 1 vhdl_noload 0 vhdl_synth 0 vhdl_enable0In 0 folder {Top Level} last_compile 1661268274 vhdl_disableopt 0 vhdl_vital 0 cover_excludedefault 0 vhdl_warn1 1 vhdl_warn2 1 vhdl_explicit 1 vhdl_showsource 0 vhdl_warn3 1 cover_covercells 0 vhdl_0InOptions {} vhdl_warn4 1 voptflow 1 cover_optlevel 3 vhdl_options {} vhdl_warn5 1 toggle - ood 0 cover_noshort 0 compile_to work compile_order 2 cover_nosub 0 dont_compile 0 vhdl_use93 2002 +Project_File_2 = /local/trb/git/trb3sc/code/scalers_readout.vhd +Project_File_P_2 = vhdl_novitalcheck 0 file_type vhdl group_id 0 cover_nofec 0 vhdl_nodebug 0 vhdl_1164 1 vhdl_noload 0 vhdl_synth 0 vhdl_enable0In 0 folder {Top Level} last_compile 1703253017 vhdl_disableopt 0 cover_excludedefault 0 vhdl_vital 0 vhdl_warn1 1 vhdl_showsource 0 vhdl_explicit 1 vhdl_warn2 1 vhdl_0InOptions {} cover_covercells 0 vhdl_warn3 1 vhdl_options {} cover_optlevel 3 voptflow 1 vhdl_warn4 1 ood 0 toggle - vhdl_warn5 1 compile_to work cover_noshort 0 compile_order 1 dont_compile 0 cover_nosub 0 vhdl_use93 2008 +Project_File_3 = /local/trb/git/trbnet/lattice/ecp3/fifo/fifo_4x2k_oreg.vhd +Project_File_P_3 = vhdl_novitalcheck 0 file_type vhdl group_id 0 cover_nofec 0 vhdl_nodebug 0 vhdl_1164 1 vhdl_noload 0 vhdl_synth 0 vhdl_enable0In 0 folder {Top Level} last_compile 1702988821 vhdl_disableopt 0 cover_excludedefault 0 vhdl_vital 0 vhdl_warn1 1 vhdl_showsource 0 vhdl_explicit 1 vhdl_warn2 1 vhdl_0InOptions {} cover_covercells 0 vhdl_warn3 1 vhdl_options {} cover_optlevel 3 voptflow 1 vhdl_warn4 1 ood 0 toggle - vhdl_warn5 1 compile_to work cover_noshort 0 compile_order 4 dont_compile 0 cover_nosub 0 vhdl_use93 2002 +Project_File_4 = /local/trb/git/trb3sc/code/tb/tb_scalers_readout.vhd +Project_File_P_4 = vhdl_novitalcheck 0 file_type vhdl group_id 0 cover_nofec 0 vhdl_nodebug 0 vhdl_1164 1 vhdl_noload 0 vhdl_synth 0 vhdl_enable0In 0 folder {Top Level} last_compile 1703254355 vhdl_disableopt 0 vhdl_vital 0 cover_excludedefault 0 vhdl_warn1 1 vhdl_warn2 1 vhdl_explicit 1 vhdl_showsource 0 vhdl_warn3 1 cover_covercells 0 vhdl_0InOptions {} vhdl_warn4 1 voptflow 1 cover_optlevel 3 vhdl_options {} vhdl_warn5 1 toggle - ood 0 cover_noshort 0 compile_to work compile_order 0 cover_nosub 0 dont_compile 0 vhdl_use93 2002 +Project_Sim_Count = 0 +Project_Folder_Count = 0 +Echo_Compile_Output = 0 +Save_Compile_Report = 1 +Project_Opt_Count = 0 +ForceSoftPaths = 0 +ProjectStatusDelay = 5000 +VERILOG_DoubleClick = Edit +VERILOG_CustomDoubleClick = +SYSTEMVERILOG_DoubleClick = Edit +SYSTEMVERILOG_CustomDoubleClick = +VHDL_DoubleClick = Edit +VHDL_CustomDoubleClick = +PSL_DoubleClick = Edit +PSL_CustomDoubleClick = +TEXT_DoubleClick = Edit +TEXT_CustomDoubleClick = +SYSTEMC_DoubleClick = Edit +SYSTEMC_CustomDoubleClick = +TCL_DoubleClick = Edit +TCL_CustomDoubleClick = +MACRO_DoubleClick = Edit +MACRO_CustomDoubleClick = +VCD_DoubleClick = Edit +VCD_CustomDoubleClick = +SDF_DoubleClick = Edit +SDF_CustomDoubleClick = +XML_DoubleClick = Edit +XML_CustomDoubleClick = +LOGFILE_DoubleClick = Edit +LOGFILE_CustomDoubleClick = +UCDB_DoubleClick = Edit +UCDB_CustomDoubleClick = +UPF_DoubleClick = Edit +UPF_CustomDoubleClick = +PCF_DoubleClick = Edit +PCF_CustomDoubleClick = +PROJECT_DoubleClick = Edit +PROJECT_CustomDoubleClick = +VRM_DoubleClick = Edit +VRM_CustomDoubleClick = +DEBUGDATABASE_DoubleClick = Edit +DEBUGDATABASE_CustomDoubleClick = +DEBUGARCHIVE_DoubleClick = Edit +DEBUGARCHIVE_CustomDoubleClick = +Project_Major_Version = 10 +Project_Minor_Version = 1 diff --git a/code/tb/tb_scalers_readout.vhd b/code/tb/tb_scalers_readout.vhd new file mode 100644 index 0000000..b7e73f6 --- /dev/null +++ b/code/tb/tb_scalers_readout.vhd @@ -0,0 +1,107 @@ +library IEEE; +use ieee.std_logic_1164.all; +use ieee.numeric_std.all; +library work; +use work.trb_net_std.all; + +entity tb is +end entity; + + + + +architecture arch of tb is + +signal clk_sys : std_logic := '1'; +signal reset_i : std_logic := '1'; + +signal signals : std_logic_vector(31 downto 0) := (others => '0'); + +signal BUS_RX : CTRLBUS_RX; +signal RDO_RX : READOUT_RX; + + +begin + +clk_sys <= not clk_sys after 5 ns; +reset_i <= '0' after 500 ns; + + +THE_DUT : entity work.scalers_readout + port map( + CLK => clk_sys, + RESET => reset_i, + + TIMER => (tick_ms => '0', tick_us => '0', others => (others => '0')), + SIGNAL_IN => signals, + + BUS_RX => BUS_RX, + BUS_TX => open, + + RDO_RX => RDO_RX, + RDO_TX => open + ); + + +process begin + signals(0) <= '1'; + signals(1) <= '1'; + wait for 10 ns; + signals(0) <= '0'; + signals(1) <= '0'; + wait for 100 ns; + signals(0) <= '1'; + signals(1) <= '1'; + wait for 10 ns; + signals(0) <= '0'; + signals(1) <= '0'; + + wait for 1.88 us; +end process; + +process begin + wait for 680 us; + RDO_RX.valid_timing_trg <= '1'; + wait for 10 ns; + RDO_RX.valid_timing_trg <= '0'; +end process; + +process begin + bus_rx.write <= '0'; + bus_rx.read <= '0'; + wait for 599 ns; + + + bus_rx.data <= x"00000300"; + bus_rx.addr <= x"0000"; + bus_rx.write <= '1'; wait for 10 ns; bus_rx.write <= '0'; wait for 10 ns; + + bus_rx.data <= x"00000030"; + bus_rx.addr <= x"0001"; + bus_rx.write <= '1'; wait for 10 ns; bus_rx.write <= '0'; wait for 10 ns; + + bus_rx.data <= x"00000064"; + bus_rx.addr <= x"0010"; + bus_rx.write <= '1'; wait for 10 ns; bus_rx.write <= '0'; wait for 10 ns; + bus_rx.data <= x"000000ff"; + bus_rx.addr <= x"0011"; + bus_rx.write <= '1'; wait for 10 ns; bus_rx.write <= '0'; wait for 10 ns; + bus_rx.data <= x"000003ff"; + bus_rx.addr <= x"0012"; + bus_rx.write <= '1'; wait for 10 ns; bus_rx.write <= '0'; wait for 10 ns; + + bus_rx.data <= x"00000001"; + bus_rx.addr <= x"0020"; + bus_rx.write <= '1'; wait for 10 ns; bus_rx.write <= '0'; wait for 10 ns; + bus_rx.data <= x"00000002"; + bus_rx.addr <= x"0021"; + bus_rx.write <= '1'; wait for 10 ns; bus_rx.write <= '0'; wait for 10 ns; + + bus_rx.data <= x"00000301"; + bus_rx.addr <= x"0000"; + bus_rx.write <= '1'; wait for 10 ns; bus_rx.write <= '0'; wait for 10 ns; + + + wait; +end process; +end architecture; diff --git a/shutdownlogic/trb3sc_basic.prj b/shutdownlogic/trb3sc_basic.prj index 68db6e3..ee227e2 100644 --- a/shutdownlogic/trb3sc_basic.prj +++ b/shutdownlogic/trb3sc_basic.prj @@ -148,6 +148,10 @@ add_file -vhdl -lib work "../../trb3sc/shutdownlogic/code/shutdown_individual.vh add_file -vhdl -lib work "../../trb3sc/shutdownlogic/code/shutdown_compare.vhd" add_file -vhdl -lib work "../../trb3sc/shutdownlogic/code/shutdown_monitoring.vhd" +#Scaler reaodut +add_file -vhdl -lib work "../../trb3sc/code/scalers_readout.vhd" +add_file -vhdl -lib work "../../trbnet/lattice/ecp3/fifo/fifo_2x64k_oreg.vhd" +add_file -vhdl -lib work "../../trbnet/lattice/ecp3/fifo/fifo_4x2k_oreg.vhd" #TrbNet Endpoint add_file -vhdl -lib work "../../trbnet/trb_net16_term_buf.vhd" diff --git a/shutdownlogic/trb3sc_basic.vhd b/shutdownlogic/trb3sc_basic.vhd index de5b04c..d07fc0d 100644 --- a/shutdownlogic/trb3sc_basic.vhd +++ b/shutdownlogic/trb3sc_basic.vhd @@ -18,16 +18,8 @@ entity trb3sc_basic is CLK_SUPPL_PCLK : in std_logic; --125 MHz for GbE CLK_CORE_PCLK : in std_logic; --Main Oscillator CLK_EXT_PLL_LEFT : in std_logic; --External Clock - --CLK_SUPPL_PLL_LEFT : in std_logic; --not used - --CLK_SUPPL_PLL_RIGHT : in std_logic; --not used - --CLK_CORE_PLL_LEFT : in std_logic; --not used - --CLK_CORE_PLL_RIGHT : in std_logic; --not used - --CLK_EXT_PCLK : in std_logic; --not used - --CLK_EXT_PLL_RIGHT : in std_logic; --not used TRIG_LEFT : in std_logic; --Trigger Input - --TRIG_PLL : in std_logic; --not used - --TRIG_RIGHT : in std_logic; --not used --Backplane, all lines -- BACK_GPIO : inout std_logic_vector(15 downto 0); @@ -130,8 +122,8 @@ architecture trb3sc_arch of trb3sc_basic is signal readout_rx : READOUT_RX; signal readout_tx : readout_tx_array_t(0 to 0); - signal ctrlbus_rx, bussci_rx, bustools_rx, bustc_rx, busrdo_rx, busshtdwn_rx, bus_master_out : CTRLBUS_RX; - signal ctrlbus_tx, bussci_tx, bustools_tx, bustc_tx, busrdo_tx, busshtdwn_tx, bus_master_in : CTRLBUS_TX; + signal ctrlbus_rx, bussci_rx, bustools_rx, bustc_rx, busshtdwn_rx, bus_master_out, busscaler_rx : CTRLBUS_RX; + signal ctrlbus_tx, bussci_tx, bustools_tx, bustc_tx, busshtdwn_tx, bus_master_in, busscaler_tx : CTRLBUS_TX; signal common_stat_reg : std_logic_vector(std_COMSTATREG*32-1 downto 0) := (others => '0'); signal common_ctrl_reg : std_logic_vector(std_COMCTRLREG*32-1 downto 0); @@ -303,8 +295,8 @@ THE_ENDPOINT : entity work.trb_net16_endpoint_hades_full_handler_record THE_BUS_HANDLER : entity work.trb_net16_regio_bus_handler_record generic map( PORT_NUMBER => 5, - PORT_ADDRESSES => (0 => x"d000", 1 => x"b000", 2 => x"d300", 3 => x"a000", 4 => x"e000", others => x"0000"), - PORT_ADDR_MASK => (0 => 12, 1 => 9, 2 => 1, 3 => 12, 4 => 12, others => 0), + PORT_ADDRESSES => (0 => x"d000", 1 => x"b000", 2 => x"d300", 3 => x"9e00", 4 => x"e000", others => x"0000"), + PORT_ADDR_MASK => (0 => 12, 1 => 9, 2 => 1, 3 => 8, 4 => 12, others => 0), PORT_MASK_ENABLE => 1 ) port map( @@ -317,13 +309,13 @@ THE_ENDPOINT : entity work.trb_net16_endpoint_hades_full_handler_record BUS_RX(0) => bustools_rx, --Flash, SPI, UART, ADC, SED BUS_RX(1) => bussci_rx, --SCI Serdes BUS_RX(2) => bustc_rx, --Clock switch - BUS_RX(3) => busrdo_rx, --User config + BUS_RX(3) => busscaler_rx, --User config BUS_RX(4) => busshtdwn_rx, BUS_TX(0) => bustools_tx, BUS_TX(1) => bussci_tx, BUS_TX(2) => bustc_tx, - BUS_TX(3) => busrdo_tx, + BUS_TX(3) => busscaler_tx, BUS_TX(4) => busshtdwn_tx, STAT_DEBUG => open @@ -351,8 +343,6 @@ THE_ENDPOINT : entity work.trb_net16_endpoint_hades_full_handler_record SPI_CLK_OUT => spi_clk, --Header HEADER_IO => HDR_IO, - --LCD - LCD_DATA_IN => lcd_data, --ADC ADC_CS => ADC_CS, ADC_MOSI => ADC_DIN, @@ -429,93 +419,11 @@ THE_ENDPOINT : entity work.trb_net16_endpoint_hades_full_handler_record end if; end process; --- TEST_LINE <= med_stat_debug(15 downto 0); --- TEST_LINE(15 downto 0) <= debug_clock_reset(15 downto 14) & med2int(0).stat_op(13) & clear_i & reset_i & debug_clock_reset(10 downto 0); --- -- -- -- -- -- -- TEST_LINE(0) <= med2int(0).stat_op(13); --- -- -- -- -- -- -- TEST_LINE(1) <= med2int(0).stat_op(15); --- -- -- -- -- -- -- TEST_LINE(2) <= clear_i; --- -- -- -- -- -- -- TEST_LINE(3) <= reset_i; --- -- -- -- -- -- -- TEST_LINE(4) <= med2int(0).dataready; -- von flo rausgenommen --- -- -- -- -- -- -- TEST_LINE(5) <= int2med(0).dataready; --- -- -- -- -- -- -- TEST_LINE(6) <= sfp_txdis_i; --- -- -- -- -- -- -- TEST_LINE(7) <= med2int(0).stat_op(9); --- readout_tx(0).data_finished <= '1'; --- readout_tx(0).data_write <= '0'; --- readout_tx(0).busy_release <= '1'; --- - --- gen_chains : for i in 1 to 16 generate --- process begin --- wait until rising_edge(clk_full); --- c(i)(5000 downto 1) <= c(i)(4999 downto 0); --- c(i)(0) <= not c(i)(0) or KEL(i); --- BACK_GPIO(i-1) <= c(i)(5000); --- if reset_i = '1' then --- c(i)(5000 downto 0) <= (others => '0'); --- end if; --- end process; --- --- end generate; - - -THE_RDO_STAT : process begin - wait until rising_edge(clk_sys); - busrdo_tx.ack <= '0'; - busrdo_tx.nack <= '0'; - busrdo_tx.unknown <= '0'; - - if busrdo_rx.write = '1' then - if busrdo_rx.addr = x"0000" then - busrdo_tx.ack <= '1'; - data_amount <= unsigned(busrdo_rx.data(15 downto 0)); - else - busrdo_tx.unknown <= '1'; - end if; - elsif busrdo_rx.read = '1' then - if busrdo_rx.addr = x"0000" then - busrdo_tx.ack <= '1'; - busrdo_tx.data(15 downto 0) <= std_logic_vector(data_amount); - else - busrdo_tx.unknown <= '1'; - end if; - end if; -end process; - -THE_RDO : process begin - wait until rising_edge(clk_sys); - readout_tx(0).busy_release <= '0'; - readout_tx(0).data_write <= '0'; - readout_tx(0).data_finished <= '0'; - - case state is - when IDLE => - if readout_rx.valid_timing_trg = '1' or readout_rx.valid_notiming_trg = '1' then - state <= WRITE; - end if; - if readout_rx.invalid_trg = '1' then - state <= FINISH; - end if; - data_counter <= 0; - when WRITE => - readout_tx(0).data <= timer.microsecond(15 downto 0) & std_logic_vector(data_counter); - readout_tx(0).data_write <= '1'; - data_counter <= data_counter + 1; - if data_counter = data_amount then - state <= FINISH; - end if; - when FINISH => - state <= BUSYEND; - readout_tx(0).data_finished <= '1'; - when BUSYEND => - state <= IDLE; - readout_tx(0).busy_release <= '1'; - end case; -end process; --------------------------------------------------------------------------- -- ShutdownLogic --------------------------------------------------------------------------- - THE_LOGIC : entity work.shutdown_logic +THE_LOGIC : entity work.shutdown_logic generic map( INPUTS => 32, OUTPUTS =>2 @@ -531,9 +439,27 @@ end process; ); - - - +--------------------------------------------------------------------------- +-- Microscalers +--------------------------------------------------------------------------- +THE_SCALERS : entity work.scalers_readout + generic map( + NUM_OUTPUTS => 4 + ) + port map( + CLK => clk_sys, + RESET => reset_i, + + BUS_RX => busscaler_rx, + BUS_TX => busscaler_tx, + + SIGNAL_IN => INP(15 downto 0) & KEL(36 downto 21), + TIMER => timer, + + RDO_RX => readout_rx, + RDO_TX => readout_tx(0) + ); + -- 2.43.0